Cisco Systems OL-6157-01 manual Cli

Page 76

Appendix C Configuring the Switch with the CLI-Based Setup Program

Where to Go Next

Where to Go Next

After you complete the setup program, the switch can run the default configuration that you created.

•For product overview information, see Chapter 1, “Overview.”

•For detailed installation procedures on mounting your switch on or under a desk or on a wall, or connecting to the small form-factor pluggable (SFP) modules, see Chapter 2, “Installation.” To complete this setup procedure, your PC must not be configured with a fixed IP address.

If you want to change the configuration or want to perform other management tasks, use one of these tools:

•CLI

•Device manager from your browser (for one switch)

•Network Assistant (for one or more switches)

To use the CLI, enter commands at the Switch> prompt through the console port by using a terminal-emulation program or through the network by using a telnet session. For configuration information, see the switch software configuration guide or the switch command reference.

To use the Network Assistant, see the Getting Started with Cisco Network Assistant guide.

Catalyst 2940 Switch Hardware Installation Guide

	C-8	OL-6157-01

Image 76

Contents Catalyst 2940 Switch Hardware Installation Guide Corporate HeadquartersCatalyst 2940 Switch Hardware Installation Guide N T E N T S Installation Accessing the CLI Through the Console Port D-2 Contents Catalyst 2940 Hardware Installation Guide Purpose AudienceConventions Bewaar Deze Instructies Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE SegurançaOL-6157-01 GEM Disse Anvisninger Xii Related Publications Obtaining Documentation Cisco.comDocumentation CD-ROM Ordering DocumentationDocumentation Feedback Obtaining Technical AssistanceCisco TAC Website Opening a TAC Case Obtaining Additional Publications and Information TAC Case Priority DefinitionsXvii Xviii Setting up the Switch FeaturesFront-Panel Description 10/100 Ethernet ports 100BASE-FX port SFP module slotPort Numbering 10/100 Ports10/100/1000 Port Port or Slot type Catalyst 2940-8TT-S Catalyst 2940-8TF-SSFP Module Slot 100BASE-FX PortType Cisco Part Number Micron SFP Modules62.5/125 micron 50/125 micron Micron Single-mode Cable Guard LEDsMode LED Port Mode Description Color System StatusPort Mode Color Meaning Power Connector Rear-Panel DescriptionConsole Port Security SlotsManagement Options OL-6157-01 Installation Preparing for InstallationChapter Installation Guidelines Verifying Package ContentsVerifying Switch Operation Installing the Switch on a Desk Without Mounting Screws Installing the SwitchInstalling the Switch on a Desk With Mounting Screws Installing the Mounting Screws on Top of a Desk Installing the Switch Under a Desk Mounting the Switch on Top of a DeskInstalling the Mounting Screws Under a Desk Installing the Switch on a Wall Mounting the Switch Under a DeskThis Side Switch Screw Slides on this way Connecting to an SFP Module Installing the Switch Magnet MountConnecting to an SFP Module Port Connecting to 10/100 Ports and the 10/100/1000 Port Connecting to a 10/100 PortConnecting to the 100BASE-FX Port 10 Connecting to a 100BASE-FX Port11 Connecting to an SFP Module Port Where to Go Next Chapter Diagnosing Common Problems Understanding Post ResultsSymptom Possible Cause Resolution B-5 throughNo connectivity to SFP Poor performance or excessive System LED is amber OL-6157-01 Physical Dimensions Power RequirementsEnvironmental Ranges Safety Fiber-Port Power Levels 100BASE-FX port Slot1SFP module Table A-3 Catalyst 2940 Switch Agency Approvals OL-6157-01 Connectors and Cables Connector SpecificationsFigure B-2 10/100 RJ-45 Pinouts Connecting to 10BASE-T and 100BASE-TX Devices 10/100/1000 PortsFigure B-4 MT-RJ Connector Cable and Adapter Specifications Two Twisted-Pair Cable PinoutsFour Twisted-Pair Cable Pinouts for 10/100 Ports TD+Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports TPOConnecting to a PC Cable and Adapter PinoutsIdentifying a Rollover Cable OL-6157-01 Configuring the Switch with the CLI-Based Setup Program Methods for Accessing the CLIAccessing the CLI Through the Console Port Taking Out What You NeedConnecting to a Power Source Connecting to the Console PortFigure C-3 Connecting a Switch to a PC Starting the Terminal Emulation SoftwareEntering the Initial Configuration Information IP SettingsCompleting the Setup Program These choices appear CLI Numerics IN-2 IN-3 IN-4 IN-5 IN-6