Cisco Systems OL-16447-01 manual Switch Installation

Page 29

Chapter 2 Switch Installation

Warnings

Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device. Statement 1019

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. 10/100/1000 Ethernet Statement 1044

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning No user-serviceable parts inside. Do not open. Statement 1073

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Caution To comply with the Telcordia GR-1089 Network Equipment Building Systems (NEBS) standard for electromagnetic compatibility and safety, connect the Ethernet cables only to intrabuilding or nonexposed wiring or cabling.

Note The grounding architecture of this product is DC-isolated (DC-I).

You can use the grounding lug to attach a wrist strap for ESD protection during servicing.

Cisco ME 3400E Ethernet Access Switch Hardware Installation Guide

 

OL-16447-01

2-3

 

 

 

Image 29
Contents Text Part Number OL-16447-01 Americas HeadquartersPage N T E N T S Installing the Switch Rack-Mounting Link Status IP Settings C-2 Purpose AudienceViii Related PublicationsObtaining Documentation and Submitting a Service Request OL-16447-01 Switch Models Setting Up the SwitchFront Panel Switch Model DescriptionCisco ME 3400EG-12CS-M Front Panel Alarm Input Port AC- and DC-Power Input Connectors10/100 Fast Ethernet Ports Management PortDual-Purpose Ports SFP ModulesPart Number Description SFP Module Patch CableLEDs UNIs, NNIs, and ENIsColor System Status Switch LED PanelsSwitch Power-Supply LEDs Power-Supply Module LEDsEthernet Management Port LED Port LEDs Alarm LEDsDual-Purpose Port LEDs LED Color MeaningRear Panel Power-supply slot Ground connection11 Cisco ME 3400EG-2CS-A Rear Panel Power Supply FeaturesManagement Options FansNetwork Configurations OL-16447-01 Switch Installation Switch Installation Switch Installation Installation Guidelines Powering Off the Switch Verifying Switch OperationInstalling the Switch Rack-Mounting Removing Screws from the SwitchRack-Mounting Brackets Attaching Brackets to the SwitchAttaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch, 23-Inch, and 24-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks Attaching Brackets for Etsi Racks Mounting in a Rack Mounting in a RackAttaching Brackets for Wall-Mounting Wall-MountingMounting the Switch on a Wall Cisco ME 3400EG-12CS-M Cisco ME 3400E-24TS-M Cisco ME 3400EG-2CS-A Table- or Shelf-Mounting Installing and Removing SFP ModulesInstalling SFP Modules 16 SFP Module with a Bale-Clasp Latch Removing SFP Modules Inserting and Removing the SFP Module Patch CableRemoving the SFP Module Patch Cable Connecting to the 10/100 and 10/100/1000 Ports21 Connecting to an Ethernet Port 22 Connecting to a Fiber-Optic SFP Module Port Connecting to Fiber-Optic SFP Modules23 Connecting to a 1000BASE-T SFP Module Connecting to 1000BASE-T SFP ModulesWhere to Go Next Connecting to Dual-Purpose PortsModel number Description Power-Supply Module DescriptionProduct Overview PSU OK LED Handle-Side DescriptionPSU OK Connector-Side Description Power-Supply Module InstallationAC-Power-Supply Module DC-Power-Supply ModuleTools and Equipment Installation GuidelinesAC-1 PSU-1 AC-2 PSU-2 Installing an AC-Power-Supply ModuleAC-Power Supply and Power-Cord Retainer in a Switch Removing AC-Power-Supply ModulesInstalling a DC-Power-Supply Module Grounding the Switch Preparing for InstallationRemove the ground screw from the switch rear panel 12 Attaching the Ground Lug and Wire Assembly Installing the DC-Power-Supply Module in the SwitchStatement Wiring the DC-Input Power Source15 Terminal Block Plug 18 Inserting Wires in the Terminal Block Plug 21 Inserting the Terminal Block in the Block Header 22 DC-Power Terminal Block With Two Feeds Removing the DC-Power-Supply ModulePower Supply Settings OL-16447-01 Switch Post Results Diagnosing ProblemsSwitch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber CablesPort and Interface Settings SFP Module Port IssuesPing the End Device Spanning Tree LoopsSwitch Performance Clearing the Switch IP Address and ConfigurationSpeed, Duplex, and Autonegotiation Autonegotiation and NICsSerial Number Location on the Cisco ME 3400E-24TS-M Finding the Switch Serial NumberOL-16447-01 SFP Module 32 to 131F 0 to 55C 32 to 140F 0 to 60C Environmental Ranges32 to 149F 0 to 65C With 1 Power-Supply With 2 Power-Supply SFP Module Modules32 to 149 F 0 to 65C DC-Power Requirements Physical DimensionsAC-Power Requirements Physical Dimensions Power Specifications Physical SpecificationsPower Specifications OL-16447-01 10/100 Connector SpecificationsFigure B-2 Fiber-Optic SFP Module LC Connector SFP Module ConnectorsFigure B-3 10/100/1000 Port Pinouts 10/100 Ethernet Management PortSFP Module Cables Cables and AdaptersCore Modal Bandwidth SFP Module Wavelength nanometers Fiber Type1000BASE-SX TP3 Cable PinoutsDSR DTR CTS RTS Console Port Adapter PinoutsSwitch Console RJ-45-to-DB-25 Port DTE Starting the Terminal-Emulation Software Accessing the CLI Through the Console PortCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable secret password, and press Return These choices appear Numerics IN-2 IN-3 IN-4 IN-5 IN-6