Cisco Systems OL-16447-01 manual Accessing the CLI Through the Console Port

Page 93

A P P E N D I X C

Configuring the Switch with the CLI-Based

Setup Program

This appendix provides a command-line interface (CLI)-based setup procedure for a standalone switch. Before connecting the switch to a power source, review the safety warnings in Chapter 2, “Switch Installation” and Chapter 3, “Installing and Removing AC- and DC-Power-Supply Modules.”

Accessing the CLI Through the Console Port

You can access the CLI on a configured or unconfigured switch by connecting the console port of the switch to the serial port on your PC or workstation and accessing the switch through a Telnet session.

Starting the Terminal-Emulation Software

Before you power on the switch, start the terminal emulation session so that you can see the output display from the power-on self-test (POST).

The terminal-emulation software—frequently a PC application such as Hyperterminal or

ProcommPlus—makes communication between the switch and your PC or terminal possible.

Follow these steps to start a terminal-emulation session:

Step 1 Start the terminal-emulation program if you are using a PC or terminal.

Step 2 Configure the baud rate and character format of the PC or terminal to match these console port default characteristics:

•9600 baud or 115200 baud (suggested rate)

•8 data bits

•1 stop bit

•No parity

•None (flow control)

Cisco ME 3400E Ethernet Access Switch Hardware Installation Guide

	OL-16447-01	C-1

Image 93

Contents Text Part Number OL-16447-01 Americas HeadquartersPage N T E N T S Installing the Switch Rack-Mounting Link Status IP Settings C-2 Purpose AudienceViii Related PublicationsObtaining Documentation and Submitting a Service Request OL-16447-01 Switch Models Setting Up the SwitchFront Panel Switch Model DescriptionCisco ME 3400EG-12CS-M Front Panel Alarm Input Port AC- and DC-Power Input Connectors10/100 Fast Ethernet Ports Management PortDual-Purpose Ports SFP ModulesPart Number Description SFP Module Patch CableLEDs UNIs, NNIs, and ENIsColor System Status Switch LED PanelsSwitch Power-Supply LEDs Power-Supply Module LEDsEthernet Management Port LED Port LEDs Alarm LEDsDual-Purpose Port LEDs LED Color MeaningRear Panel Power-supply slot Ground connection11 Cisco ME 3400EG-2CS-A Rear Panel Power Supply FeaturesManagement Options FansNetwork Configurations OL-16447-01 Switch Installation Switch Installation Switch Installation Installation Guidelines Verifying Switch Operation Installing the SwitchPowering Off the Switch Rack-Mounting Removing Screws from the SwitchRack-Mounting Brackets Attaching Brackets to the SwitchAttaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch, 23-Inch, and 24-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks Attaching Brackets for Etsi Racks Mounting in a Rack Mounting in a RackAttaching Brackets for Wall-Mounting Wall-MountingMounting the Switch on a Wall Cisco ME 3400EG-12CS-M Cisco ME 3400E-24TS-M Cisco ME 3400EG-2CS-A Installing and Removing SFP Modules Installing SFP ModulesTable- or Shelf-Mounting 16 SFP Module with a Bale-Clasp Latch Removing SFP Modules Inserting and Removing the SFP Module Patch CableRemoving the SFP Module Patch Cable Connecting to the 10/100 and 10/100/1000 Ports21 Connecting to an Ethernet Port 22 Connecting to a Fiber-Optic SFP Module Port Connecting to Fiber-Optic SFP Modules23 Connecting to a 1000BASE-T SFP Module Connecting to 1000BASE-T SFP ModulesWhere to Go Next Connecting to Dual-Purpose PortsPower-Supply Module Description Product OverviewModel number Description PSU OK LED Handle-Side DescriptionPSU OK Connector-Side Description Power-Supply Module InstallationAC-Power-Supply Module DC-Power-Supply ModuleTools and Equipment Installation GuidelinesAC-1 PSU-1 AC-2 PSU-2 Installing an AC-Power-Supply ModuleAC-Power Supply and Power-Cord Retainer in a Switch Removing AC-Power-Supply ModulesInstalling a DC-Power-Supply Module Grounding the Switch Preparing for InstallationRemove the ground screw from the switch rear panel 12 Attaching the Ground Lug and Wire Assembly Installing the DC-Power-Supply Module in the SwitchStatement Wiring the DC-Input Power Source15 Terminal Block Plug 18 Inserting Wires in the Terminal Block Plug 21 Inserting the Terminal Block in the Block Header 22 DC-Power Terminal Block With Two Feeds Removing the DC-Power-Supply ModulePower Supply Settings OL-16447-01 Switch Post Results Diagnosing ProblemsSwitch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber CablesPort and Interface Settings SFP Module Port IssuesPing the End Device Spanning Tree LoopsSwitch Performance Clearing the Switch IP Address and ConfigurationSpeed, Duplex, and Autonegotiation Autonegotiation and NICsSerial Number Location on the Cisco ME 3400E-24TS-M Finding the Switch Serial NumberOL-16447-01 SFP Module 32 to 131F 0 to 55C 32 to 140F 0 to 60C Environmental Ranges32 to 149F 0 to 65C With 1 Power-Supply With 2 Power-Supply SFP Module Modules32 to 149 F 0 to 65C Physical Dimensions AC-Power RequirementsDC-Power Requirements Physical Dimensions Power Specifications Physical SpecificationsPower Specifications OL-16447-01 10/100 Connector SpecificationsFigure B-2 Fiber-Optic SFP Module LC Connector SFP Module ConnectorsFigure B-3 10/100/1000 Port Pinouts 10/100 Ethernet Management PortSFP Module Cables Cables and AdaptersCore Modal Bandwidth SFP Module Wavelength nanometers Fiber Type1000BASE-SX TP3 Cable PinoutsDSR DTR CTS RTS Console Port Adapter PinoutsSwitch Console RJ-45-to-DB-25 Port DTE Starting the Terminal-Emulation Software Accessing the CLI Through the Console PortEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter an enable secret password, and press Return These choices appear Numerics IN-2 IN-3 IN-4 IN-5 IN-6