Cisco Systems OL-16447-01 manual Attaching Brackets for Wall-Mounting

Page 40

Chapter 2 Switch Installation

Installing the Switch

After the switch is mounted in the rack, you need to do these tasks to complete the installation:

Power on the switch. See the “Verifying Switch Operation” section on page 2-5.

Connect to the RJ-45 connector of a dual-purpose port, and run the initial configuration dialog. See the Cisco ME 3400E Ethernet Access Switch Getting Started Guide for instructions.

Connect to the front-panel ports. See the “Connecting to the 10/100 and 10/100/1000 Ports” section on page 2-22, the “Connecting to Fiber-Optic SFP Modules” section on page 2-24, and the “Connecting to 1000BASE-T SFP Modules” section on page 2-25to complete the installation.

We recommend attaching the cable guide to prevent the cables from obscuring the front panel of the switch and the other devices installed in the rack. Use the supplied black screw shown in Figure 2-9to attach the cable guide to the left or right bracket.

For configuration instructions about using the CLI setup program, go to Appendix C, “Configuring the Switch with the CLI-Based Setup Program.”

Wall-Mounting

Attaching Brackets for Wall-Mounting, page 2-14

Mounting the Switch on a Wall, page 2-15

Note Wall-mounting has not been evaluated for NEBS applications.

Attaching Brackets for Wall-Mounting

Figure 2-11 Attaching 19-inch Bracket to Wall-Mount Cisco ME 3400EG-12CS-M or

Cisco ME 3400E-24TS-M

280842

1

1

Phillips truss-head screws

Follow the same steps to attach the second bracket to the opposite side.

 

Cisco ME 3400E Ethernet Access Switch Hardware Installation Guide

2-14

OL-16447-01

Image 40
Contents Americas Headquarters Text Part Number OL-16447-01Page N T E N T S Installing the Switch Rack-Mounting Link Status IP Settings C-2 Audience PurposeRelated Publications ViiiObtaining Documentation and Submitting a Service Request OL-16447-01 Setting Up the Switch Switch ModelsSwitch Model Description Front PanelCisco ME 3400EG-12CS-M Front Panel AC- and DC-Power Input Connectors Alarm Input PortManagement Port 10/100 Fast Ethernet PortsDual-Purpose Ports SFP ModulesSFP Module Patch Cable Part Number DescriptionUNIs, NNIs, and ENIs LEDsSwitch LED Panels Color System StatusPower-Supply Module LEDs Switch Power-Supply LEDsEthernet Management Port LED Alarm LEDs Port LEDsDual-Purpose Port LEDs LED Color MeaningPower-supply slot Ground connection Rear PanelPower Supply Features 11 Cisco ME 3400EG-2CS-A Rear PanelFans Management OptionsNetwork Configurations OL-16447-01 Switch Installation Switch Installation Switch Installation Installation Guidelines Installing the Switch Verifying Switch OperationPowering Off the Switch Removing Screws from the Switch Rack-MountingAttaching Brackets to the Switch Rack-Mounting BracketsAttaching Brackets for 19-Inch Racks Attaching Brackets for 19-Inch, 23-Inch, and 24-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for 24-Inch Racks Attaching Brackets for Etsi Racks Mounting in a Rack Mounting in a RackWall-Mounting Attaching Brackets for Wall-MountingMounting the Switch on a Wall Cisco ME 3400EG-12CS-M Cisco ME 3400E-24TS-M Cisco ME 3400EG-2CS-A Installing SFP Modules Installing and Removing SFP ModulesTable- or Shelf-Mounting 16 SFP Module with a Bale-Clasp Latch Inserting and Removing the SFP Module Patch Cable Removing SFP ModulesConnecting to the 10/100 and 10/100/1000 Ports Removing the SFP Module Patch Cable21 Connecting to an Ethernet Port Connecting to Fiber-Optic SFP Modules 22 Connecting to a Fiber-Optic SFP Module PortConnecting to 1000BASE-T SFP Modules 23 Connecting to a 1000BASE-T SFP ModuleConnecting to Dual-Purpose Ports Where to Go NextProduct Overview Power-Supply Module DescriptionModel number Description Handle-Side Description PSU OK LEDPSU OK Power-Supply Module Installation Connector-Side DescriptionAC-Power-Supply Module DC-Power-Supply ModuleInstallation Guidelines Tools and EquipmentInstalling an AC-Power-Supply Module AC-1 PSU-1 AC-2 PSU-2Removing AC-Power-Supply Modules AC-Power Supply and Power-Cord Retainer in a SwitchInstalling a DC-Power-Supply Module Preparing for Installation Grounding the SwitchRemove the ground screw from the switch rear panel Installing the DC-Power-Supply Module in the Switch 12 Attaching the Ground Lug and Wire AssemblyWiring the DC-Input Power Source Statement15 Terminal Block Plug 18 Inserting Wires in the Terminal Block Plug 21 Inserting the Terminal Block in the Block Header Removing the DC-Power-Supply Module 22 DC-Power Terminal Block With Two FeedsPower Supply Settings OL-16447-01 Diagnosing Problems Switch Post ResultsSwitch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber CablesSFP Module Port Issues Port and Interface SettingsPing the End Device Spanning Tree LoopsClearing the Switch IP Address and Configuration Switch PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and NICsFinding the Switch Serial Number Serial Number Location on the Cisco ME 3400E-24TS-MOL-16447-01 Environmental Ranges SFP Module 32 to 131F 0 to 55C 32 to 140F 0 to 60CWith 1 Power-Supply With 2 Power-Supply SFP Module Modules 32 to 149F 0 to 65C32 to 149 F 0 to 65C AC-Power Requirements Physical DimensionsDC-Power Requirements Physical Dimensions Physical Specifications Power SpecificationsPower Specifications OL-16447-01 Connector Specifications 10/100SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC Connector10/100 Ethernet Management Port Figure B-3 10/100/1000 Port PinoutsCables and Adapters SFP Module CablesCore Modal Bandwidth SFP Module Wavelength nanometers Fiber Type1000BASE-SX Cable Pinouts TP3Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Accessing the CLI Through the Console Port Starting the Terminal-Emulation SoftwareIP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter an enable secret password, and press Return These choices appear Numerics IN-2 IN-3 IN-4 IN-5 IN-6