Cisco Systems 3515 MCU12, 3515 MCU24 manual About the Initial Configuration and Boot Phases

Page 16

Chapter 2 Setting Up Your Cisco Unified Videoconferencing 3515 MCU

How to Perform the Cisco Unified Videoconferencing 3515 MCU Unit Initial Configuration

Figure 2-2 Fitting a Bracket for Rack Mounting

157263

Step 4 Pass the screws through the brackets and tighten them into the screw holes on each side of the Cisco Unified Videoconferencing 3515 MCU unit using a suitable screwdriver.

Step 5 Insert the Cisco Unified Videoconferencing 3515 MCU unit into the 19-inch rack.

Step 6 Fasten the brackets to the side rails of the rack.

Step 7 Make sure that the air vents at the sides of the Cisco Unified Videoconferencing 3515 MCU unit are not blocked.

How to Perform the Cisco Unified Videoconferencing 3515 MCU Unit Initial Configuration

•About the Initial Configuration and Boot Phases, page 2-4

•Connecting to a PC, page 2-5

•Setting the IP Address, page 2-5

•Setting Ethernet Speed and Duplex Parameters, page 2-7

•Connecting the Cisco Unified Videoconferencing 3515 MCU Unit to the LAN, page 2-8

About the Initial Configuration and Boot Phases

Initial monitoring and administration of the Cisco Unified Videoconferencing 3515 MCU unit are performed from a remote PC via a serial connection. This allows you to access the boot configuration menu of the Cisco Unified Videoconferencing 3515 MCU unit. At power-up, the Cisco Unified Videoconferencing 3515 MCU unit goes through the following boot phases:

•Auto-boot—The embedded operating system initializes and displays basic information.

•Configuration menu—A six-second countdown allows you to enter the configuration menu.

•Initialization—The Cisco Unified Videoconferencing 3515 MCU unit completes its boot sequence and is ready for operation.

Installation and Upgrade Guide for Cisco Unified Videoconferencing 3515 MCU Release 5.6

2-4

OL-17012-01

 

 

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Americas Headquarters Text Part Number OL-17012-01Page N T E N T S Safety Functionality AdministratorsAbout theCisco Unified Videoconferencing 3515 MCU Main Features Feature DescriptionModerators and Operators Conference UsersSccp Port Capacities Cisco Unified Videoconferencing 3515 MCU12 Port Capacity Cisco Unified Videoconferencing 3515 MCU24 Port CapacityAbout Cisco Unified Videoconferencing 3515 MCU Architecture Centralized Topology Cascaded ConferencesCascaded Conference Setting Up Your Cisco Unified Videoconferencing 3515 MCU Physical DescriptionVerifying the Package Contents Product Contents Before You BeginAbout the Initial Configuration and Boot Phases Fitting a Bracket for Rack MountingConnecting to a PC Setting the IP AddressProcedure Setting Ethernet Speed and Duplex Parameters About the Initial Video Processing Module Configuration Accessing the Video Processing Module Main Menu Changing the Configuration Software Password Changing the Security LevelChanging Advanced Configuration Settings Advanced Configuration menu appears as followsSaving Network Configuration Settings Connecting the EMP to the LANSnmp Management Performing Software UpgradesLocal Port Monitoring Connections Before You Begin Registering the Online Help for the 3515 MCU OL-17012-01 About the Cisco Software Upgrade Utility Using the Cisco Software Upgrade UtilityLaunching the Cisco Software Upgrade Utility Click Customize Snmp Settings Upgrading SoftwareRS-232 9-Pin Serial Port Cable Connections and Pin-outsPin Function TXD+ RJ-45 8-Pin IP Network PortRXD+ Technical Specifications Failsafe Electrical Safety SafetyGrounding Batteries ESD ProceduresHigh Voltage Compliance and Certifications Safety ComplianceCISPR24 Telecom FCC Part 15 NoticeActa Part 68 Notice CE CTR3, CE CTR4Environmental Compliance Industry CanadaOL-17012-01 Numerics IN-2 Snmp IN-4
Top Page Image Contents