Cisco Systems OL-4552-01 manual Following example is used for a Cisco IGX node, 10-16

Page 16

Chapter 10 Cisco WAN Manager Operations

Downloading Software and Firmware

40

Enable Degraded Mode

[

Y]

(Y/N) 55 LCN reprgrm batch cnt

[

100]

(D)

41

Trk Cell Rtng Restrict

[

Y]

(Y/N) 56 Dnld LanIP or NwIP

[

Nw](Lan/Nw)

42

Enable Feeder Alert

[

N]

(Y/N) 57

IP Relay gateway node

[

0]

(D)

43

Reroute on Comm Fail

[

N]

(Y/N) 58

Max LAN Window (sec)

[

60]

(D)

44

Auto Switch on Degrade

[

Y]

(Y/N)

59

Max LAN Packets/Window

[18000]

(D)

45

Max Degraded Aborts

[

100]

(D)

60

Extended Cline Object

[

N]

(Y/N)

This Command: cnfnodeparm 15 N

Next Command:

The following example is used for a Cisco IGX node:

node TN

Cisco

 

IGX

8430 9.4.00

Feb. 14 2003 17:27 GMT

 

 

1

Update Initial Delay

[ 5000]

(D)

16

CC Redundancy Cnfged

[

Y]

(Y/N)

2

Update Per-Node Delay

[30000]

(D)

17

MT3 Pass Through Relay

[

Y]

(Y/N)

3

Comm-Break Test Delay

[30000]

(D)

18

Nw Pkt Tx Rate (pps)

[

500]

(D)

4

Comm-Break Test Offset

[

 

10]

(D)

19

Stats Memory (x 100KB)

[

130]

(D)

5

Network Timeout Period

[ 1700]

(D)

20

Standby Update Timer

[

10]

(D)

6

Network Inter-p Period

[ 4000]

(D)

21

Stby Updts Per Pass

[

150]

(D)

7

NW Sliding Window Size

[

 

1]

(D)

22

Gateway ID Timer

[

30]

(D)

8

Num Normal Timeouts

[

 

7]

(D)

23

GLCON Alloc Timer

[

30]

(D)

9

Num Inter-p Timeouts

[

 

3]

(D)

24

Comm Fail Delay

[

60]

(D)

10

Num Satellite Timeouts

[

 

6]

(D)

25

Nw Hdlr Timer (msec)

[

100]

(D)

11

Num Blind Timeouts

[

 

4]

(D)

26

CBUS Delay (msec)

[

20]

(D)

12

Num CB Msg Timeouts

[

 

2]

(D)

27

SNMP Event logging

[

Y]

(Y/N)

13

Comm Fail Interval

[10000]

(D)

28

TFTP Grant Delay (sec)

[

1]

(D)

14

Comm Fail Multiplier

[

 

3]

(D)

29

TFTP ACK Timeout (sec)

[

10]

(D)

15

Temperature Threshold

[

 

50]

(D)

30

TFTP Write Retries

[

3]

(D)

31

FRP Link Status Alarm

[

 

Y]

(Y/N)

46

Modem polling timer

[

1]

(D)

32

Job Lock Timeout

[

 

60]

(D)

47

Verify CBA for non-FRP

[

N]

(Y/N)

33

Max Via LCONs

[20000]

(D)

48

Send Abit early

[

N]

(Y/N)

34

Max Blind Segment Size

[ 3570]

(D)

49

Abit Tmr Multiplier M

[

0]

(D)

35

Max XmtMemBlks per NIB

[ 3000]

(D)

50

Abit Tmr Granularity N

[

3]

(D)

36

Max Mem on Stby Q (%)

[

 

33]

(D)

51

CommBrk Hop Weight

[

25]

(D)

37

Trk Cell Rtng Restrict

[

 

Y]

(Y/N)

52

CB Fail Penalty Hops

[

2]

(D)

38

Stat Config Proc Cnt

[ 1000]

(D)

53

Dnld LanIP or NwIP

[ Lan](Lan/Nw)

39

Stat Config Proc Delay

[ 2000]

(D)

54

IP Relay gateway node

[

0]

(D)

40

Enable Degraded Mode

[

 

Y]

(Y/N) 55 Max LAN Window (sec)

[

60]

(D)

41

Enable Rrt on Comm Fail[

 

N]

(Y/N) 56 Max LAN Packets/Window

[18000]

(D)

42

Auto Switch on Degrade

[

 

Y]

(Y/N)

 

 

 

 

 

43

Max Degraded Aborts

[

100]

(D)

 

 

 

 

 

44

Max Htls Rebuild Count

[

100]

(D)

 

 

 

 

 

45

Htls Counter Reset Time[ 1000]

(D)

 

 

 

 

 

This Command: cnfnodeparm

16 N

 

 

 

 

 

 

 

Next Command:

When you have a redundant processor card and the value for the parameter CC Redundancy Cnfged is Yes, you are requesting an image download into both processors (active and redundant).

Note If CC Redundancy Cnfged is Yes and no redundant processor card is present, the download is suspended.

Step 9 Enter the cnffwswinit <IP_addr_CWM_workstation> command to configure the switch to receive software or firmware images from the CWM workstation.

 

Cisco WAN Manager User’s Guide

10-16

Release 15, Part Number OL-4552-01 Rev. C0, January 27, 2005

Image 16
Contents Cisco WAN Manager Operations 10-1Launching the Configuration Save and Restore Utility 10-2Saving Node Configurations from CWM 10-3Configuration Save Window 10-410-5 Saving Node Configurations for Cisco BPX and Cisco IGX Nodes 10-610-7 Reserved for firmware imageFollowing example is shown 10-810-9 Restoring Node Configurations from CWM 10-10Configuration Restore window 10-11Downloading Software and Firmware 10-12 Locating Switch Images for Downloading 10-1310-14 Following example is used for the Cisco IGX node 10-15Following example is used for a Cisco IGX node 10-1610-17 10-18 Cisco MGX Conventions Cisco IGX and Cisco BPX Conventions10-19 Launching the Image Download 10-20Processing the Downloaded Image Image Download Access Tabs10-21 10-22 Image Download In-ProgressClick Download 10-23Deleting Images 10-2410-25 10-26