Cisco Systems SOHO Series manual FCC Class B Statement, Australia Compliance Statement

Page 4

•Australia Compliance Statement

Electromagnetic Compatibility

•Australia Compliance Statement

•Statement 157—VCCI Compliance for Class B Equipment

Agency Approvals and Standards

This section lists the following agency approvals and standards for EMC:

•CFR47 part 15 subpart B, 2000 class B

•EN55022, 1998 class B, CISPR22, 1997 class B

•EN55024, 1998 Immunity Std, CISPR24, 1997 Immunity Std

•EN61000-3-2, Harmonics, EN61000-3-3, Flicker

•EN61000-4-2, Electro Static Discharge

•EN61000-4-3, Radiated Immunity

•EN61000-4-4, Electrical Fast Transients

•EN61000-4-5, Surge

•EN61000-4-6, Conducted Immunity

•EN61000-4-11, Dips and Sags

•AS/NZS 3548

•CCC

FCC Class B Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and the receiver

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Caution Modification of this equipment without Cisco’s authorization may result in this equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers

4	OL-10260-02

Image 4

Contents Safety Safety, page Electromagnetic Compatibility, pageTranslated Safety Warnings, page Obtaining Documentation and Submitting a Service Request, pagePower Cable and AC Adapter Agency Approvals and StandardsOperating Conditions for Canada Operating Conditions for the European CommunityPower Cable and AC Adapter Electromagnetic CompatibilityOperating Conditions for the United Kingdom Agency Approvals and Standards FCC Class B StatementFCC Class B Statement Australia Compliance StatementStatement 157-VCCI Compliance for Class B Equipment CFR47 part 15 subpart B, 2000 class BCISPR 22 Class B Statement Canada Compliance StatementsAustralia Compliance Statement Canadian Class B StatementEMC Class A Notices and Warnings Statement 157-VCCI Compliance for Class B EquipmentClass A Notice for FCC Class A Notice for FCC CISPR 22 Class A StatementTelecommunications CISPR 22 Class A StatementCanadian Class A Statement Statement 191-VCCI Class A Warning for JapanFCC Part 68 Notice Models That Have Only Ethernet PortsModels That are for Europe Only Cisco 800 Series Routers That Are Not Telecom RegulatedService Order Codes Cisco 800 Series and Cisco SOHO Series Routers Facility Interface andAgency Approval and Standards Power Level Settings Guidelines for Operating Cisco Wireless Access Points in JapanAdministrative Rules for Cisco Wireless Devices in Taiwan RadioPower Level Settings Canadian Compliance StatementMaximum Power Setting dBM Radio FCC IDDanish Direktiv 1999/5/EF Guidelines for Operating Cisco Wireless Access Points in Japan RF ExposureWireless Devices with IEEE 802.11b/g Radios Administrative Rules for Cisco Wireless Devices in Taiwan03-6434-6500 All Access Wireless Products Declarations of Conformity Conformité Européenne CE Marking DirectiveEuropean Union Statements Network Termination Point StatementTranslated Safety Warnings Statement 12-Power Supply Disconnection WarningStatement 19-TN Power Warning Statement 23-ISDN Connection Warning Statement 150-Power Off Before Working on SystemStatement 1040-Product Disposal Statement 1042-Ring Signal Generator Statement 1073-No User-Serviceable PartsStatement 1071-Warning Definition Statement 1074-Comply with Local and National Electrical CodesWarnung WICHTIGE SICHERHEITSHINWEISE Varning! VIKTIGA SÄKERHETSANVISNINGAR Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo Translated Safety Warnings Statement 12-Power Supply Disconnection Warning Statement 19-TN Power Warning Statement 23-ISDN Connection Warning Page Statement 43-Jewelry Removal Warning Statement 94-Wrist Strap Warning Attention Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil métallique Statement 119-Unit Short Circuit Protection Statement 150-Power Off Before Working on System Statement 151-ISDN Network Voltages Warning Statement 162-EU Public Network Port Warning Statement 199-Emergency Access Warning Statement 242-Equipment Grounding Warning Statement 245B-Explosive Device Proximity Wireless Network DeviceStatement 332-Antenna Installation Warning Statement 1001-Work During Lightning Activity Statement 1004-Installation Instructions Statement 1005-Circuit Breaker Statement 1015-Battery Handling Avvertenza Pericolo di esplosione se la batteria non è installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore Statement 1021-SELV Circuit Statement 1023-No. 26 AWG Statement 1024-Ground Conductor Attention Cet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse ni utiliser léquipement sans un conducteur de masse adéquatement installé. En cas de doute sur la mise à la masse appropriée disponible, sadresser à lorganisme responsable de la sécurité électrique ou à un électricien Translated Safety Warnings Statement 1030-Equipment Installation Statement 1035-Proximity to Water Statement 1036-Telephone Jacks in Wet Locations Statement 1037-Uninsulated Wires or Terminals Statement 1038-Telephone Use During an Electrical Storm Statement 1040-Product Disposal Advarsel Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og bestemmelser Statement 1042-Ring Signal Generator Statement 1073-No User-Serviceable Parts Avvertenza Non contiene parti riparabili dallutente. Non aprire Statement 1074-Comply with Local and National Electrical Codes Obtaining Documentation and Submitting a Service Request