Cisco Systems SOHO Series manual RF Exposure

Page 13
RF Exposure

Radio

[Romanian]:

Slovensko [Slovenian]:

Slovensky [Slovak]:

Suomi [Finnish]:

Svenska [Swedish]:

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.

RF Exposure

The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The equipment should be installed more than 20 cm (7.9 in.) from your body or nearby persons. The access point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz integrated antennas support a minimum separation distance of 8 cm (3.2 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously.

Note Dual antennas used for diversity operation are not considered co-located.

Guidelines for Operating Cisco Wireless Access Points in Japan

This section provides guidelines for avoiding interference when operating Cisco wireless access points in Japan. These guidelines are provided in both English and Japanese.

English Translation

This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.

1.1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.

2.If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.

Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers

 

OL-10260-02

13

 

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Safety, page Electromagnetic Compatibility, page SafetyTranslated Safety Warnings, page Obtaining Documentation and Submitting a Service Request, pageAgency Approvals and Standards Power Cable and AC AdapterOperating Conditions for Canada Operating Conditions for the European CommunityElectromagnetic Compatibility Power Cable and AC AdapterOperating Conditions for the United Kingdom Agency Approvals and Standards FCC Class B StatementAustralia Compliance Statement FCC Class B StatementStatement 157-VCCI Compliance for Class B Equipment CFR47 part 15 subpart B, 2000 class BCanada Compliance Statements CISPR 22 Class B StatementAustralia Compliance Statement Canadian Class B StatementStatement 157-VCCI Compliance for Class B Equipment EMC Class A Notices and WarningsClass A Notice for FCC Class A Notice for FCC CISPR 22 Class A StatementCISPR 22 Class A Statement TelecommunicationsCanadian Class A Statement Statement 191-VCCI Class A Warning for JapanModels That Have Only Ethernet Ports FCC Part 68 NoticeModels That are for Europe Only Cisco 800 Series Routers That Are Not Telecom RegulatedCisco 800 Series and Cisco SOHO Series Routers Facility Interface and Service Order CodesGuidelines for Operating Cisco Wireless Access Points in Japan Agency Approval and Standards Power Level SettingsAdministrative Rules for Cisco Wireless Devices in Taiwan RadioCanadian Compliance Statement Power Level SettingsMaximum Power Setting dBM Radio FCC IDDanish Direktiv 1999/5/EF RF Exposure Guidelines for Operating Cisco Wireless Access Points in JapanWireless Devices with IEEE 802.11b/g Radios Administrative Rules for Cisco Wireless Devices in Taiwan03-6434-6500 All Access Wireless Products Conformité Européenne CE Marking Directive Declarations of ConformityEuropean Union Statements Network Termination Point StatementStatement 12-Power Supply Disconnection Warning Translated Safety WarningsStatement 19-TN Power Warning Statement 23-ISDN Connection Warning Statement 150-Power Off Before Working on SystemStatement 1073-No User-Serviceable Parts Statement 1040-Product Disposal Statement 1042-Ring Signal GeneratorStatement 1071-Warning Definition Statement 1074-Comply with Local and National Electrical CodesWarnung WICHTIGE SICHERHEITSHINWEISE Varning! VIKTIGA SÄKERHETSANVISNINGAR Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo OL-10260-02 Statement 12-Power Supply Disconnection Warning Statement 19-TN Power Warning Statement 23-ISDN Connection Warning Page Statement 43-Jewelry Removal Warning Statement 94-Wrist Strap Warning Attention Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil métallique Statement 119-Unit Short Circuit Protection Statement 150-Power Off Before Working on System Statement 151-ISDN Network Voltages Warning Statement 162-EU Public Network Port Warning Statement 199-Emergency Access Warning Statement 245B-Explosive Device Proximity Wireless Network Device Statement 242-Equipment Grounding WarningStatement 332-Antenna Installation Warning Statement 1001-Work During Lightning Activity Statement 1004-Installation Instructions Statement 1005-Circuit Breaker Statement 1015-Battery Handling Avvertenza Pericolo di esplosione se la batteria non è installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore Statement 1021-SELV Circuit Statement 1023-No. 26 AWG Statement 1024-Ground Conductor Attention Cet équipement doit être mis à la masse. Ne jamais rendre inopérant le conducteur de masse ni utiliser léquipement sans un conducteur de masse adéquatement installé. En cas de doute sur la mise à la masse appropriée disponible, sadresser à lorganisme responsable de la sécurité électrique ou à un électricien OL-10260-02 Statement 1030-Equipment Installation Statement 1035-Proximity to Water Statement 1036-Telephone Jacks in Wet Locations Statement 1037-Uninsulated Wires or Terminals Statement 1038-Telephone Use During an Electrical Storm Statement 1040-Product Disposal Advarsel Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og bestemmelser Statement 1042-Ring Signal Generator Statement 1073-No User-Serviceable Parts Avvertenza Non contiene parti riparabili dallutente. Non aprire Statement 1074-Comply with Local and National Electrical Codes Obtaining Documentation and Submitting a Service Request
Top Page Image Contents