Billion Electric Company 6404VGP, 6404VP user manual Wireless Wireless Router Only, Parameters

Page 33

Wireless (Wireless Router Only)

VoIP/(802.11g) Broadband Firewall Router

Wireless (Wireless Router Only)

Parameters

WLAN Service: Default setting is set to Enable. If you do not have any wireless, both 802.11g and 802.11b, device in your network, select Disable.

Mode: The default setting is 802.11b+g (Mixed mode). If you do not know or have both 11g and 11b devices in your network, then keep the default in mixed mode. From the drop-down manual, you can select 802.11g if you have only 11g card. If you have only 11b card, then select 802.11b.

ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change the default wlan-apto a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure your wireless clients have exactly the ESSID as the device, in order to get connected to your network.

Note: It is case sensitive and must not excess 32 characters.

ESSID Broadcast: It is function in which transmits its ESSID to the air so that when wireless client searches for a network, router can then be discovered and recognized. Default setting is Enabled.

Disable: If you do not want broadcast your ESSID. Any client uses “any” wireless setting cannot discover the Access Point (AP) of your router.

Enable: Any client that using the “any” setting can discover the Access Point (AP) in

Regulation Domain: There are seven Regulation Domains for you to choose from, including North America (N.America), Europe, France, etc. The Channel ID will be different based on this setting.

Channel ID: Select the wireless connection ID channel that you would like to use. Use the Scan Channel Usage to help to select non-occupied wireless channel.

Scan Channel Usage: Wireless channel scan takes up to 14 seconds to survey the channel ID in the network area. The result will show all ID channel is being occupied or not occupied.

Note: Wireless performance may degrade if select ID channel is already being occupied by other AP(s).

TX PowerLevel: It is function that enhances the wireless transmitting signal strength. User may

32

Chapter 4: Configuration

Image 33

Contents VoIP/802.11g Broadband Firewall Router BiPAC 6404VP / 6404VGPUser’s Manual Version Release 5.08aTable of Contents QoS Quality of Service Firewall and Access ControlCHAPTER 5 TROUBLESHOOTING VoIP Voice over Internet ProtocolChapter 1 Introduction FeaturesIntroduction to your Router 802.11g Wireless AP with WPA SupportDynamic Host Configuration Protocol DHCP client and server Quality of Service QoSNetwork Address Translation NAT SOHO Firewall Security with DoS and SPIRich Management Interfaces Firmware UpgradeableImportant note for using this router Chapter 2 Installing the RouterPackage Contents Do not use the same power source for this router as other equipmentRJ-45 connector The Front LEDsWireless Router Only RJ-11 connectorPort Power Switch PWR RESET The Rear PortsWAN LAN Phone 1XCabling Chapter 3 Basic Installation Chapter 3 Basic InstallationATA Mode Broadband Router Mode Connecting Your RouterConfiguring PCs in Windows in Window XP 2. Double-click Local Area Connection. See Figure4. Select Internet Protocol TCP/IP and click Properties. See Figure Configuring PCs in Windows 2. Double-click Local Area “LAN” Connection. See Figure4. Select Internet Protocol TCP/IP and click Properties See Figure Configuring PC in Windows 95/98/ME 5. Then select the DNS Configuration tab. See Figure3. Click Properties 2. Select TCP/IP Protocol and click Properties. See Figure Configuring PC in Windows NT4.0Web Interface Username and Password Factory Default SettingsDevice LAN IP settings ISP setting in WAN siteInformation from your ISP DHCP Obtain an IP Address Automatically Static IP Fixed IP AddressPPPoE Configuring with your Web Browser ATA / Router Mode Configuration Chapter 4 ConfigurationSave Config to FLASH StatusStatus Wireless Association Table Wireless Router OnlyARP Table Routing TableRIP Routing Table DHCP TableLeased Table Expired TableVoIP Status Email StatusEvent Log Error LogNAT Sessions DiagnosticUPnP Portmap ATA / Router Mode LAN NAT DHCP Server Device IP WAN System Firewall QoS Virtual Server FunctionsTime Schedule Advanced VoIP RouterLAN Local Area Network ConfigurationEthernet Primary IP AddressIP Alias → Active PC in LAN Ethernet Client Filter Default setting is set to DisableEthernet Client Filter Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Parameters Wireless Wireless Router OnlyWireless Distribution System WDS WPA-PSK TKIP / WPA-PSK AES Pre-Shared Key Wireless Security Wireless Router OnlyPage Wireless Client / MAC Address Filter Wireless Router Only Wireless Client Filter Default setting is set to Disable→Associated Wireless Clients DHCP Server Time Zone SystemRemote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings Packet Filter Table 1 Predefined Port Filter Example Predefined Port Filters RulesApplication ProtocolUDP17 Packet Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page Click Add TCP/UDP Filter Click DeleteExample Configuring Packet Filter5. The new port filter rule for HTTP is shown below Block Duration Intrusion DetectionIntrusion Name Table 2 Hacker attack types recognized by the IDSDetect Parameter Ascend KillAlways On URL Filterdropped Instant Message Blocking The default is set to Disabled Peer to Peer Blocking The default is set to DisabledIM / P2P Blocking Log information can be seen in the Status - Event Log after enabling Firewall LogVoIP Broadband Firewall Router VoIP Voice over Internet ProtocolSetting for Phone Port WizardVoice QoS Authentication Username Same as Phone Number User-defined ProfilesNOTE User defined profiles are limited to 8 only SIP Device Parameters Advanced - Parameters How to register to SIP ServerNote ONHOOK means hung up Advanced - PSTN Environment AdjustmentPhone Port Login Account ConfigurationVolume Control For examplesCodec Preference Speed DialPSTN Dial Plan 3 Dial at Timeout PSTN Dial Plan Examples4 Dial at Timeout no Prefix 1 Dial with PrefixVoIP/802.11g Broadband Firewall Router VoIP Dial Plan Prefix Processing Dial Plan Rules ListDescription Dial-Plan ExamplesSpecial Dial Plan Examples ## xxLocalcheap.com is the default VoIP provider I set on phone port 1. When I call out any number start with 1 or 2 or 3 and plus rest of the phone number for local call, 03 is always prepended in front of these number. If 23295 are dialed, 03-2-32935 is the actual phone number called out via localcheap.com provider Mobilecheap.com is the default VoIP provider I set on phone port 2. When I call out 123-39-45678 for a mobile call, 123 is replaced with 09. Therefore, 09-39-45678 is the actual phone number called out via Mobilecheap.com provider Country Specific Ring & Tone Ring & ToneRing Parameters Tone ParametersSpecial Dial Codes OptionFlash-hook Click Clear QoS Quality of ServicePrioritization HighDSCP Mapping Table Table 4 DSCP Mapping TableWireless Router Device Standard DSCPOutbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN Connection Diagram VoIP Normal PCs Restricted PCInformation and Settings Example QoS for your NetworkMission-critical application Advanced setting by using IP throttlingVoice application Restricted ApplicationVoIP/802.11g Broadband Firewall Router Virtual Server “Port Forwarding” Internal IP Add Virtual ServerIP Address ExampleEdit DMZ Host Global IP Address Edit One-to-One NAT Network Address TranslationSelect the Apply button to apply your changes Example List of some well-known and registered port numbers Table 5 Well-known and registered PortsPort Number ProtocolTime Schedule Configuration of Time Schedule Click EditEdit a Time Slot Delete a Time SlotManagement and IGMP Static Route AdvancedDynamic DNS Check Email Embedded Web Server 2 Management IP accounts Device ManagementSNMP V1 and Universal Plug and Play UPnPSNMP SNMP Version SNMPv2c and SNMPv3From RFC 1493 Bridge MIB From RFC1650 EtherLike-MIBFrom RFC 1471 PPP/LCP MIB From RFC 1472 PPP/Security MIBSave Configuration to Flash LogoutIGMP Problems starting up the router Chapter 5 TroubleshootingProblems with the LAN Interface ProblemContact Billion WORLDWIDE APPENDIX A Product Support and Contact Information