Billion Electric Company 6404VP, 6404VGP user manual General Settings, SIP Device Parameters

Page 64

SIP Device Parameters

VoIP/(802.11g) Broadband Firewall Router

General Settings

This section reflects and contains basic settings for the VoIP module from selected provider in the Wizard section. Fail to provide correct information will halt making calls out to the Internet.

SIP Device Parameters

SIP: To use VoIP SIP as VoIP call signaling protocol. Default is set to Disable.

Silence Suppression (VAD): Voice Activation Detection (VAD) prevents transmitting the nature silence to consume the bandwidth. It is also known as Silence Suppression which is a software application that ensures the bandwidth is reserved only when voice activity is activated. Default is set to Enable.

Echo Cancellation: G.168 echo canceller is an ITU-T standard. It is used for isolating the echo while you are on the phone. This helps you not to hear much of your own voice reflecting on the phone while you talk. Default is set to Enable.

RTP Port: Provide the based value from the media (RTP) ports that are assigned for various endpoints and the different call sessions that may exist within an end-point. (Range from 5100 to 65535, default value is 5100)

Region: This selection is a drop-down box, which allows user to select the country for which the VoIP

63

Chapter 4: Configuration

Image 64

Contents BiPAC 6404VP / 6404VGP VoIP/802.11g Broadband Firewall RouterUser’s Manual Version Release 5.08aTable of Contents Firewall and Access Control QoS Quality of ServiceCHAPTER 5 TROUBLESHOOTING VoIP Voice over Internet ProtocolFeatures Chapter 1 IntroductionIntroduction to your Router 802.11g Wireless AP with WPA SupportQuality of Service QoS Dynamic Host Configuration Protocol DHCP client and serverNetwork Address Translation NAT SOHO Firewall Security with DoS and SPIFirmware Upgradeable Rich Management InterfacesChapter 2 Installing the Router Important note for using this routerPackage Contents Do not use the same power source for this router as other equipmentThe Front LEDs RJ-45 connectorWireless Router Only RJ-11 connectorThe Rear Ports Port Power Switch PWR RESETWAN LAN Phone 1XCabling Chapter 3 Basic Installation Chapter 3 Basic InstallationConnecting Your Router ATA Mode Broadband Router Mode2. Double-click Local Area Connection. See Figure Configuring PCs in Windows in Window XP4. Select Internet Protocol TCP/IP and click Properties. See Figure 2. Double-click Local Area “LAN” Connection. See Figure Configuring PCs in Windows4. Select Internet Protocol TCP/IP and click Properties See Figure 5. Then select the DNS Configuration tab. See Figure Configuring PC in Windows 95/98/ME3. Click Properties Configuring PC in Windows NT4.0 2. Select TCP/IP Protocol and click Properties. See FigureFactory Default Settings Web Interface Username and PasswordDevice LAN IP settings ISP setting in WAN siteDHCP Obtain an IP Address Automatically Static IP Fixed IP Address Information from your ISPPPPoE Configuring with your Web Browser Chapter 4 Configuration ATA / Router Mode ConfigurationSave Config to FLASH StatusWireless Association Table Wireless Router Only StatusARP Table Routing TableDHCP Table RIP Routing TableLeased Table Expired TableEmail Status VoIP StatusError Log Event LogDiagnostic NAT SessionsUPnP Portmap ATA / Router Mode Functions LAN NAT DHCP Server Device IP WAN System Firewall QoS Virtual ServerTime Schedule Advanced VoIP RouterConfiguration LAN Local Area NetworkEthernet Primary IP AddressIP Alias Ethernet Client Filter Default setting is set to Disable → Active PC in LANEthernet Client Filter Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Wireless Wireless Router Only ParametersWireless Distribution System WDS Wireless Security Wireless Router Only WPA-PSK TKIP / WPA-PSK AES Pre-Shared KeyPage Wireless Client Filter Default setting is set to Disable Wireless Client / MAC Address Filter Wireless Router Only→Associated Wireless Clients DHCP Server System Time ZoneRemote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings Packet Filter Example Predefined Port Filters Rules Table 1 Predefined Port FilterApplication ProtocolUDP17 Packet Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page Click Delete Click Add TCP/UDP FilterExample Configuring Packet Filter5. The new port filter rule for HTTP is shown below Intrusion Detection Block DurationTable 2 Hacker attack types recognized by the IDS Intrusion NameDetect Parameter Ascend KillURL Filter Always Ondropped Peer to Peer Blocking The default is set to Disabled Instant Message Blocking The default is set to DisabledIM / P2P Blocking Firewall Log Log information can be seen in the Status - Event Log after enablingVoIP Voice over Internet Protocol VoIP Broadband Firewall RouterWizard Setting for Phone PortVoice QoS User-defined Profiles Authentication Username Same as Phone NumberNOTE User defined profiles are limited to 8 only SIP Device Parameters How to register to SIP Server Advanced - ParametersAdvanced - PSTN Environment Adjustment Note ONHOOK means hung upLogin Account Configuration Phone PortFor examples Volume ControlCodec Preference Speed DialPSTN Dial Plan PSTN Dial Plan Examples 3 Dial at Timeout4 Dial at Timeout no Prefix 1 Dial with PrefixChapter 4 Configuration VoIP Dial Plan Dial Plan Rules List Prefix ProcessingDial-Plan Examples DescriptionSpecial Dial Plan Examples ## xxLocalcheap.com is the default VoIP provider I set on phone port 1. When I call out any number start with 1 or 2 or 3 and plus rest of the phone number for local call, 03 is always prepended in front of these number. If 23295 are dialed, 03-2-32935 is the actual phone number called out via localcheap.com provider Mobilecheap.com is the default VoIP provider I set on phone port 2. When I call out 123-39-45678 for a mobile call, 123 is replaced with 09. Therefore, 09-39-45678 is the actual phone number called out via Mobilecheap.com provider Ring & Tone Country Specific Ring & ToneRing Parameters Tone ParametersOption Special Dial CodesFlash-hook QoS Quality of Service Click ClearPrioritization HighTable 4 DSCP Mapping Table DSCP Mapping TableWireless Router Device Standard DSCPOutbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN VoIP Normal PCs Restricted PC Connection DiagramInformation and Settings Example QoS for your NetworkAdvanced setting by using IP throttling Mission-critical applicationVoice application Restricted ApplicationChapter 4 Configuration Virtual Server “Port Forwarding” Add Virtual Server Internal IPExample IP AddressEdit DMZ Host Edit One-to-One NAT Network Address Translation Global IP AddressSelect the Apply button to apply your changes Table 5 Well-known and registered Ports Example List of some well-known and registered port numbersPort Number ProtocolTime Schedule Click Edit Configuration of Time ScheduleEdit a Time Slot Delete a Time SlotAdvanced Management and IGMP Static RouteDynamic DNS Check Email Device Management Embedded Web Server 2 Management IP accountsUniversal Plug and Play UPnP SNMP V1 andSNMP SNMP Version SNMPv2c and SNMPv3From RFC1650 EtherLike-MIB From RFC 1493 Bridge MIBFrom RFC 1471 PPP/LCP MIB From RFC 1472 PPP/Security MIBLogout Save Configuration to FlashIGMP Chapter 5 Troubleshooting Problems starting up the routerProblems with the LAN Interface ProblemAPPENDIX A Product Support and Contact Information Contact Billion WORLDWIDE