Billion Electric Company 6404VP, 6404VGP user manual Wireless Distribution System WDS

Page 34

VoIP/(802.11g) Broadband Firewall Router

adjust this power level from minimum 0 up to maximum 255.

Note: The Power Level maybe different in each access network user premises environment and choose the most suitable level for your network.

Connected: Representing in true or false. That it is the connection status between the system and the build-in wireless card.

AP MAC Address: It is a unique hardware address of the Access Point.

AP Firmware Version: The Access Point firmware version.

Wireless Distribution System (WDS)

It is a wireless access point mode that enables wireless link and communication with other access point. It is easy to be installed simply define peer’s MAC address of the connected AP. WDS takes advantages of cost saving and flexibility which no extra wireless client device is required to bridge between two access points and extending an existing wired or wireless infrastructure network to create a larger network.

In addition, WDS enhances its link connection security in WEP mode, WEP key encryption must be the same for both access points.

WDS Service: The default setting is Disabled. Check Enable radio button to activate this function.

Peer WDS MAC Address: It is the associated AP’s MAC Address. It is important that your peer’s AP must include your MAC address in order to acknowledge and communicate with each other.

Note: For MAC Address, Semicolon ( : ) must be included.

33

Chapter 4: Configuration

Image 34

Contents User’s Manual BiPAC 6404VP / 6404VGPVoIP/802.11g Broadband Firewall Router Version Release 5.08aTable of Contents CHAPTER 5 TROUBLESHOOTING Firewall and Access ControlQoS Quality of Service VoIP Voice over Internet ProtocolIntroduction to your Router FeaturesChapter 1 Introduction 802.11g Wireless AP with WPA SupportNetwork Address Translation NAT Quality of Service QoSDynamic Host Configuration Protocol DHCP client and server SOHO Firewall Security with DoS and SPIFirmware Upgradeable Rich Management InterfacesPackage Contents Chapter 2 Installing the RouterImportant note for using this router Do not use the same power source for this router as other equipmentWireless Router Only The Front LEDsRJ-45 connector RJ-11 connectorWAN LAN The Rear PortsPort Power Switch PWR RESET Phone 1XCabling Chapter 3 Basic Installation Chapter 3 Basic InstallationConnecting Your Router ATA Mode Broadband Router Mode2. Double-click Local Area Connection. See Figure Configuring PCs in Windows in Window XP4. Select Internet Protocol TCP/IP and click Properties. See Figure 2. Double-click Local Area “LAN” Connection. See Figure Configuring PCs in Windows4. Select Internet Protocol TCP/IP and click Properties See Figure 5. Then select the DNS Configuration tab. See Figure Configuring PC in Windows 95/98/ME3. Click Properties Configuring PC in Windows NT4.0 2. Select TCP/IP Protocol and click Properties. See FigureDevice LAN IP settings Factory Default SettingsWeb Interface Username and Password ISP setting in WAN siteDHCP Obtain an IP Address Automatically Static IP Fixed IP Address Information from your ISPPPPoE Configuring with your Web Browser Save Config to FLASH Chapter 4 ConfigurationATA / Router Mode Configuration StatusARP Table Wireless Association Table Wireless Router OnlyStatus Routing TableLeased Table DHCP TableRIP Routing Table Expired TableEmail Status VoIP StatusError Log Event LogDiagnostic NAT SessionsUPnP Portmap ATA / Router Mode Time Schedule Advanced FunctionsLAN NAT DHCP Server Device IP WAN System Firewall QoS Virtual Server VoIP RouterEthernet ConfigurationLAN Local Area Network Primary IP AddressIP Alias Ethernet Client Filter Default setting is set to Disable → Active PC in LANEthernet Client Filter Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Wireless Wireless Router Only ParametersWireless Distribution System WDS Wireless Security Wireless Router Only WPA-PSK TKIP / WPA-PSK AES Pre-Shared KeyPage Wireless Client Filter Default setting is set to Disable Wireless Client / MAC Address Filter Wireless Router Only→Associated Wireless Clients DHCP Server System Time ZoneRemote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings Packet Filter Application Example Predefined Port Filters RulesTable 1 Predefined Port Filter ProtocolUDP17 Packet Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page Example Click DeleteClick Add TCP/UDP Filter Configuring Packet Filter5. The new port filter rule for HTTP is shown below Intrusion Detection Block DurationDetect Parameter Table 2 Hacker attack types recognized by the IDSIntrusion Name Ascend KillURL Filter Always Ondropped Peer to Peer Blocking The default is set to Disabled Instant Message Blocking The default is set to DisabledIM / P2P Blocking Firewall Log Log information can be seen in the Status - Event Log after enablingVoIP Voice over Internet Protocol VoIP Broadband Firewall RouterWizard Setting for Phone PortVoice QoS User-defined Profiles Authentication Username Same as Phone NumberNOTE User defined profiles are limited to 8 only SIP Device Parameters How to register to SIP Server Advanced - ParametersAdvanced - PSTN Environment Adjustment Note ONHOOK means hung upLogin Account Configuration Phone PortCodec Preference For examplesVolume Control Speed DialPSTN Dial Plan 4 Dial at Timeout no Prefix PSTN Dial Plan Examples3 Dial at Timeout 1 Dial with PrefixChapter 4 Configuration VoIP Dial Plan Dial Plan Rules List Prefix ProcessingSpecial Dial Plan Examples Dial-Plan ExamplesDescription ## xxLocalcheap.com is the default VoIP provider I set on phone port 1. When I call out any number start with 1 or 2 or 3 and plus rest of the phone number for local call, 03 is always prepended in front of these number. If 23295 are dialed, 03-2-32935 is the actual phone number called out via localcheap.com provider Mobilecheap.com is the default VoIP provider I set on phone port 2. When I call out 123-39-45678 for a mobile call, 123 is replaced with 09. Therefore, 09-39-45678 is the actual phone number called out via Mobilecheap.com provider Ring Parameters Ring & ToneCountry Specific Ring & Tone Tone ParametersOption Special Dial CodesFlash-hook Prioritization QoS Quality of ServiceClick Clear HighWireless Router Device Table 4 DSCP Mapping TableDSCP Mapping Table Standard DSCPOutbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN Information and Settings VoIP Normal PCs Restricted PCConnection Diagram Example QoS for your NetworkVoice application Advanced setting by using IP throttlingMission-critical application Restricted ApplicationChapter 4 Configuration Virtual Server “Port Forwarding” Add Virtual Server Internal IPExample IP AddressEdit DMZ Host Edit One-to-One NAT Network Address Translation Global IP AddressSelect the Apply button to apply your changes Port Number Table 5 Well-known and registered PortsExample List of some well-known and registered port numbers ProtocolTime Schedule Edit a Time Slot Click EditConfiguration of Time Schedule Delete a Time SlotAdvanced Management and IGMP Static RouteDynamic DNS Check Email Device Management Embedded Web Server 2 Management IP accountsSNMP Universal Plug and Play UPnPSNMP V1 and SNMP Version SNMPv2c and SNMPv3From RFC 1471 PPP/LCP MIB From RFC1650 EtherLike-MIBFrom RFC 1493 Bridge MIB From RFC 1472 PPP/Security MIBLogout Save Configuration to FlashIGMP Problems with the LAN Interface Chapter 5 TroubleshootingProblems starting up the router ProblemAPPENDIX A Product Support and Contact Information Contact Billion WORLDWIDE