Cisco Systems manual Guidelines for Using 1130AG Series Lightweight Access Points

Page 16

Chapter 1 Overview

Guidelines for Using 1130AG Series Lightweight Access Points

The lightweight 1131AG access point contains two integrated radios: a 2.4-GHz radio (IEEE 802.11g) and a 5-GHz radio (IEEE 801.11a). The lightweight 1131G access point contains one integrated radio: a 2.4-GHz radio (IEEE 802.11g). Using a controller, you can configure the radio settings.

In the Cisco Centralized Wireless LAN architecture, access points operate in the lightweight mode (as opposed to autonomous mode). The lightweight access points associate to a controller. The controller manages the configuration, firmware, and controls transactions such as 802.1x authentication. In addition, all wireless traffic is tunneled through the controller.

LWAPP is an Internet Engineering Task Force (IETF) draft protocol that defines the control messaging for setup and path authentication and run-time operations. LWAPP also defines the tunneling mechanism for data traffic.

In an LWAPP environment, a lightweight access point discovers a controller by using LWAPP discovery mechanisms and then sends it an LWAPP join request. The controller sends the lightweight access point an LWAPP join response allowing the access point to join the controller. When the access point is joined, the access point downloads its software if the versions on the access point and controller do not match. After an access point joins a controller, you can reassign it to any controller on your network.

LWAPP secures the control communication between the lightweight access point and controller by means of a secure key distribution, using X.509 certificates on both the access point and controller.

This chapter provides information on the following topics:

•Guidelines for Using 1130AG Series Lightweight Access Points, page 1-2

•Hardware Features, page 1-3

•Network Examples with Autonomous Access Points, page 1-7

Guidelines for Using 1130AG Series Lightweight Access Points

You should keep these guidelines in mind when you use a 1130AG series lightweight access point:

•The access points can communicate only with 2006 or 4400 series controllers. Cisco 4100 series, Airespace 4012 series, and Airespace 4024 series controllers are not supported because they lack the memory required to support access points running Cisco IOS software.

•The access points do not support Wireless Domain Services (WDS). The access points communicate only with controllers and cannot communicate with WDS devices. However, the controller provides functionality equivalent to WDS when the access point associates to it.

•The access points support eight BSSIDs per radio and a total of eight wireless LANs per access point. When a lightweight access point associates to a controller, only wireless LANs with IDs 1 through 8 are pushed to the access point.

•The access points do not support Layer 2 LWAPP. They must get an IP address and discover the controller using DHCP, DNS, or IP subnet broadcast.

•The access point console port is enabled for monitoring and debuging purposes (all configuration commands are disabled after connecting to a controller).

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

1-2

OL-8369-05

 

 

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Americas Headquarters Page N T E N T S Access Point Layout and Connectors Guidelines for Using 1130AG Series Lightweight Access Points Declarations of Conformity and Regulatory Information B-1 Vii Viii Preface AudiencePurpose OrganizationConventions Preface Conventions Related Publications Locating the Product Serial Number SN AaannnnxxxxXiv Autonomous Access Points Lightweight Access PointsOverview Product TerminologyGuidelines for Using 1130AG Series Lightweight Access Points Hardware Features Access Point Hardware FeaturesSingle or Dual-Radio Operation Power Sources Anti-Theft Features Network Examples with Autonomous Access Points Access Point Security Screw HoleRoot Unit on a Wired LAN Access pointRepeater Unit that Extends Wireless Range Access Point as RepeaterCentral Unit in an All-Wireless Network Workgroup Bridge ConfigurationNetwork Example with Lightweight Access Points OL-8369-05 Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Unpacking the Access Point Package ContentsBasic Installation Guidelines Controller Discovery Process for Lightweight Access PointsDeploying the Access Points on the Wireless Network Access Point Layout and Connectors 1identifies the main access point hardware featuresMounting Plate Suspended Ceiling Adjustable T-Rail Clips Rail Clip Features Push here to open Push here to close Opening the Access Point Cover Opening the Access Point CoverMounting the Access Point on a Horizontal Surface Mounting the Access Point Below a Suspended Ceiling Adjustable T-Rail ClipsMounting the Access Point Above a Suspended Ceiling T-Bar Grid Mounting Bracket Parts Mounting Access Point on a Desktop or Shelf Mounting Access Point on a Network Cable BoxAttaching the Access Point to the Mounting Plate 10 Aligning the Keyhole Clip to the Access Point Keyhole Securing the Access Point Using a Security CableSecuring the Access Point to the Mounting Plate 12 Installing the Security Hasp AdapterPadlock Connecting the Ethernet and Power Cables Option15 Looping the Ethernet Cable Connecting to an Ethernet Network with Local Power Rotating the Cisco Logo 16 Cisco Logo HolesTroubleshooting Autonomous Access Points Checking the Autonomous Access Point LEDs Status LED Ethernet LED Access point cover Radio LEDLow Power Condition for Autonomous Default IP Address Behavior Checking Basic SettingsDefault Ssid and Radio Behavior Security Settings Enable Radio InterfacesWEP Keys Low Power Condition for Autonomous Access Points Intelligent Power ManagementInline Power Status Messages OL-8369-05 Page Configuring Power Using the CLI Issuing the Cisco IOS Command Using the CLI Power Negotiation selected Power inline never3 Running the Carrier Busy Test Resetting to the Default Configuration Running the Ping TestUsing the Mode Button Using the Web Browser InterfaceReloading the Access Point Image Click Reset to DefaultsWeb Browser Interface Browser Http InterfaceObtaining the Access Point Image File Browser Tftp InterfaceConnecting to the Access Point Console Port Obtaining the Tftp Server Software Http//tftpd32.jounin.netOL-8369-05 Troubleshooting Lightweight Access Points Checking the Lightweight Access Point LEDs Using Dhcp OptionStatus LED Ethernet LED Access point cover Radio LED Cable Bay Area Low Power Condition for Lightweight Access Low Power Condition for Lightweight Access Points Configuring Power Using Controller CLI Commands Config ap power injector enable ap switch port MAC addressConfig ap power pre-standard enable Power inline auto Returning the Access Point to Autonomous Mode Configuring Controller InformationManually Resetting the Access Point to Defaults Clearing Manually Entered Controller InformationOL-8369-05 Obtaining the Autonomous Access Point Image File Mode Button SettingConnecting to the Access Point Console Port Obtaining the Tftp Server Software OL-8369-05 Translated Safety Warnings OL-8369-05 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementPage EMC Declaration of Conformity for RF Exposure Japanese Translation English Translation Access Points with Ieee 802.11a Radios Chinese Translation English TranslationAll Access Points Declaration of Conformity Statements Declaration of Conformity Annex to DofC# Information on Antennas and Power Levels OL-8369-05 Access Point Specifications CCK OET-65C OL-8369-05 Channels and Maximum Power Levels OL-8369-05 Console Cable Pinouts Console Port Signals and Pinouts OverviewPriming Lightweight Access Points Prior to Deployment OL-8369-05 Page OL-8369-05 Access Points Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 and 1500 Series Access Points Type + Length + Value O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2
Related manuals
Manual 14 pages 8.61 Kb Manual 10 pages 10.06 Kb

1130AG specifications

The Cisco Systems 1130AG access point is a robust networking device designed to provide reliable wireless connectivity in a variety of environments. Specifically engineered for both indoor and outdoor applications, the 1130AG is particularly well-suited for use in enterprise, education, and hospitality sectors, where seamless connectivity and coverage are essential.

One of the standout features of the 1130AG is its dual-band operation. It supports both the 2.4 GHz and 5 GHz frequency bands, allowing it to utilize various channels for optimal performance and reduced interference. This dual-band capability enables it to service more devices simultaneously, accommodating the growing demand for wireless connectivity in mobile computing and Internet of Things (IoT) applications.

The access point incorporates advanced technologies such as IEEE 802.11a/g standards, which ensure compatibility with a wide array of wireless clients, ensuring widespread accessibility. The 1130AG also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single Ethernet cable. This feature not only streamlines setup but also enhances flexibility, as access points can be installed in locations where power sources are limited.

Security is a paramount concern in wireless networking, and the Cisco 1130AG addresses this through robust security protocols. It supports WPA, WPA2, and other encryption standards, ensuring secure data transmission and protecting against unauthorized access. This is particularly important for organizations that handle sensitive information and require strict compliance with data protection regulations.

Another notable characteristic is the ability of the 1130AG to seamlessly integrate with Cisco's extensive range of network management tools such as Cisco Prime, allowing administrators to monitor and manage their wireless network effectively. This integration provides insights into network performance, user access patterns, and device health, enabling proactive management and troubleshooting.

Moreover, the access point's compact design and durability make it suitable for various deployment scenarios. Designed to withstand varying environmental conditions, the 1130AG can be installed in demanding settings without compromising reliability.

In conclusion, the Cisco Systems 1130AG access point embodies advanced features and technologies that cater to the needs of modern businesses. Its dual-band capabilities, strong security protocols, and ease of management, alongside its durable design, make it an essential component for creating a high-performing wireless network. Whether in office buildings, educational institutions, or hospitality venues, the 1130AG provides the performance and reliability necessary to support today’s connected world.
Top Page Image Contents