Cisco Systems 1130AG manual Inline Power Status Messages

Page 57

Chapter 3 Troubleshooting Autonomous Access Points

Low Power Condition for Autonomous Access Points

The access point supports Intelligent Power Management and as a result of the power negotiations, the access point will either enter full power mode or remain in low power mode with the radios disabled.

Note Independent of the power negotiations, the access point hardware also uses the 802.3af classification scheme to indicate the power required from the power source. However, the power source cannot report the power available to the access point unless the power source also supports Intelligent Power Management.

Some Cisco switches that are capable of supplying sufficient power require a software upgrade to support Intelligent Power Management. If the software upgrade is not desired, you can configure the access point to operate in pre-standard compatibility mode and the access point automatically enters full power mode if these Cisco switches are detected in the received CDP ID field.

When the access point determines that sufficient power is not available for full power operation, an error message is logged and the Status LED turns amber to indicate low power mode (see the “Checking the Autonomous Access Point LEDs” section on page 3-2and the “Inline Power Status Messages” section on page 3-7).

Tip If your switch is capable of supplying sufficient power for full operation but the access point remains in low-power mode, your access point or your switch (or both) might be misconfigured (see Table 3-2and Table 3-3).

If your inline power source is not able to supply sufficient power for full operation, you should consider these options:

•Upgrade to a higher-powered switch

•Use a Cisco Aironet power injector on the switch port

•Use the 48-VDC power module to locally power the access point

Inline Power Status Messages

These messages are logged on the console port by the access point to report the power condition:

•%CDP_PD-4-POWER_OK: Full Power - AC_ADAPTOR inline power source—This message indicates the access point is using the power module and can support full-power operation.

•%CDP_PD-4-POWER_OK: Full Power - NEGOTIATED inline power source—This message indicates the access point is operating at full power and has successfully negotiated for 12.95 W of power from a Cisco switch supporting Cisco Intelligent Power Management.

•%CDP_PD-4-POWER_OK: Full Power - HIGH_POWER_CLASSIC inline power source—This message indicates the access point is operating at full power because it has been configured for pre-standard compatibility mode and has detected a Cisco switch that does not support Intelligent Power Management but is able to supply sufficient power to the access point.

•%CDP_PD-4-POWER_OK: Full Power - INJECTOR_CONFIGURED_ON_SOURCE inline power source—This message indicates the access point is operating at full power because it is connected to a Cisco switch that supports Intelligent Power Management and the switch has been configured with the power inline never command.

•%CDP_PD-4-POWER_OK: Full power - INJECTOR_CONFIGURED_ON_CURRENT_PORT inline power source—This message indicates the access point is operating at full power because it has been configured to expect a power injector on this port.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

 

OL-8369-05

3-7

 

 

 

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Americas Headquarters Page N T E N T S Access Point Layout and Connectors Guidelines for Using 1130AG Series Lightweight Access Points Declarations of Conformity and Regulatory Information B-1 Vii Viii Audience PrefacePurpose OrganizationConventions Preface Conventions Related Publications SN Aaannnnxxxx Locating the Product Serial NumberXiv Lightweight Access Points Autonomous Access PointsOverview Product TerminologyGuidelines for Using 1130AG Series Lightweight Access Points Access Point Hardware Features Hardware FeaturesSingle or Dual-Radio Operation Power Sources Anti-Theft Features Access Point Security Screw Hole Network Examples with Autonomous Access PointsAccess point Root Unit on a Wired LANAccess Point as Repeater Repeater Unit that Extends Wireless RangeWorkgroup Bridge Configuration Central Unit in an All-Wireless NetworkNetwork Example with Lightweight Access Points OL-8369-05 Installing the Access Point Safety Information FCC Safety Compliance StatementGeneral Safety Guidelines Package Contents Unpacking the Access PointController Discovery Process for Lightweight Access Points Basic Installation GuidelinesDeploying the Access Points on the Wireless Network 1identifies the main access point hardware features Access Point Layout and ConnectorsMounting Plate Suspended Ceiling Adjustable T-Rail Clips Rail Clip Features Push here to open Push here to close Opening the Access Point Cover Opening the Access Point CoverMounting the Access Point on a Horizontal Surface Adjustable T-Rail Clips Mounting the Access Point Below a Suspended CeilingMounting the Access Point Above a Suspended Ceiling T-Bar Grid Mounting Bracket Parts Mounting Access Point on a Network Cable Box Mounting Access Point on a Desktop or ShelfAttaching the Access Point to the Mounting Plate 10 Aligning the Keyhole Clip to the Access Point Keyhole Using a Security Cable Securing the Access Point12 Installing the Security Hasp Adapter Securing the Access Point to the Mounting PlatePadlock Option Connecting the Ethernet and Power Cables15 Looping the Ethernet Cable Connecting to an Ethernet Network with Local Power 16 Cisco Logo Holes Rotating the Cisco LogoTroubleshooting Autonomous Access Points Status LED Ethernet LED Access point cover Radio LED Checking the Autonomous Access Point LEDsLow Power Condition for Autonomous Checking Basic Settings Default IP Address BehaviorDefault Ssid and Radio Behavior Enable Radio Interfaces Security SettingsWEP Keys Intelligent Power Management Low Power Condition for Autonomous Access PointsInline Power Status Messages OL-8369-05 Page Configuring Power Using the CLI Issuing the Cisco IOS Command Using the CLI Power Negotiation selected Power inline never3 Running the Carrier Busy Test Running the Ping Test Resetting to the Default ConfigurationUsing the Web Browser Interface Using the Mode ButtonClick Reset to Defaults Reloading the Access Point ImageBrowser Http Interface Web Browser InterfaceBrowser Tftp Interface Obtaining the Access Point Image FileConnecting to the Access Point Console Port Http//tftpd32.jounin.net Obtaining the Tftp Server SoftwareOL-8369-05 Troubleshooting Lightweight Access Points Using Dhcp Option Checking the Lightweight Access Point LEDsStatus LED Ethernet LED Access point cover Radio LED Cable Bay Area Low Power Condition for Lightweight Access Low Power Condition for Lightweight Access Points Config ap power injector enable ap switch port MAC address Configuring Power Using Controller CLI CommandsConfig ap power pre-standard enable Power inline auto Configuring Controller Information Returning the Access Point to Autonomous ModeManually Resetting the Access Point to Defaults Clearing Manually Entered Controller InformationOL-8369-05 Mode Button Setting Obtaining the Autonomous Access Point Image FileConnecting to the Access Point Console Port Obtaining the Tftp Server Software OL-8369-05 Translated Safety Warnings OL-8369-05 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Canadian Compliance Statement Industry CanadaPage EMC Declaration of Conformity for RF Exposure Japanese Translation English Translation Chinese Translation English Translation Access Points with Ieee 802.11a RadiosAll Access Points Declaration of Conformity Statements Declaration of Conformity Annex to DofC# Information on Antennas and Power Levels OL-8369-05 Access Point Specifications CCK OET-65C OL-8369-05 Channels and Maximum Power Levels OL-8369-05 Console Cable Pinouts Overview Console Port Signals and PinoutsPriming Lightweight Access Points Prior to Deployment OL-8369-05 Page OL-8369-05 Access Points Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 and 1500 Series Access Points Type + Length + Value O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2
Related manuals
Manual 14 pages 8.61 Kb Manual 10 pages 10.06 Kb

1130AG specifications

The Cisco Systems 1130AG access point is a robust networking device designed to provide reliable wireless connectivity in a variety of environments. Specifically engineered for both indoor and outdoor applications, the 1130AG is particularly well-suited for use in enterprise, education, and hospitality sectors, where seamless connectivity and coverage are essential.

One of the standout features of the 1130AG is its dual-band operation. It supports both the 2.4 GHz and 5 GHz frequency bands, allowing it to utilize various channels for optimal performance and reduced interference. This dual-band capability enables it to service more devices simultaneously, accommodating the growing demand for wireless connectivity in mobile computing and Internet of Things (IoT) applications.

The access point incorporates advanced technologies such as IEEE 802.11a/g standards, which ensure compatibility with a wide array of wireless clients, ensuring widespread accessibility. The 1130AG also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single Ethernet cable. This feature not only streamlines setup but also enhances flexibility, as access points can be installed in locations where power sources are limited.

Security is a paramount concern in wireless networking, and the Cisco 1130AG addresses this through robust security protocols. It supports WPA, WPA2, and other encryption standards, ensuring secure data transmission and protecting against unauthorized access. This is particularly important for organizations that handle sensitive information and require strict compliance with data protection regulations.

Another notable characteristic is the ability of the 1130AG to seamlessly integrate with Cisco's extensive range of network management tools such as Cisco Prime, allowing administrators to monitor and manage their wireless network effectively. This integration provides insights into network performance, user access patterns, and device health, enabling proactive management and troubleshooting.

Moreover, the access point's compact design and durability make it suitable for various deployment scenarios. Designed to withstand varying environmental conditions, the 1130AG can be installed in demanding settings without compromising reliability.

In conclusion, the Cisco Systems 1130AG access point embodies advanced features and technologies that cater to the needs of modern businesses. Its dual-band capabilities, strong security protocols, and ease of management, alongside its durable design, make it an essential component for creating a high-performing wireless network. Whether in office buildings, educational institutions, or hospitality venues, the 1130AG provides the performance and reliability necessary to support today’s connected world.
Top Page Image Contents