Cisco Systems 1130AG manual Running the Ping Test, Resetting to the Default Configuration

Page 65

Chapter 3 Troubleshooting Autonomous Access Points

Running the Ping Test

Running the Ping Test

You can use the ping test to evaluate the link to and from an associated wireless device. The ping test provides two modes of operation:

a.Performs a test using a specified number of packets and then displays the test results.

b.Performs a test that continuously operates until you stop the test and then displays the test results. Follow these steps to activate the ping test:

Step 1 Use your web browser to access the access point browser interface. Step 2 Click Association and the main association page appears.

Step 3 Click the MAC address of an associated wireless device and the Statistics page for that device appears. Step 4 Click the Ping/Link Test tab and the Ping/Link Test page appears.

Step 5 If you want to specify the number of packets to use in the test, follow these steps:

a.Enter the number of packets in the Number of Packets field

b.Enter the packet size in the Packet Size field and click Start. Step 6 If you want to use a continuous test, follow these steps:

a.Enter the packet size in the Packet Size field.

b.Click Start to activate the test.

c.Click Stop to stop the test.

When the test has completed, the test results are displayed at the bottom of the page. You should check for any lost packets that can indicate a problem with the wireless link. For best results, you should also perform this test several times.

Resetting to the Default Configuration

If you forget the password that allows you to configure the access point, you may need to completely reset the configuration. You can use the MODE button on the access point or the web-browser interface.

Note The following steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID.

For additional information on access point default behavior, refer to the “Default IP Address Behavior” section on page 3-4and the “Default SSID and Radio Behavior” section on page 3-4.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

 

OL-8369-05

3-15

 

 

 

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Americas Headquarters Page N T E N T S Access Point Layout and Connectors Guidelines for Using 1130AG Series Lightweight Access Points Declarations of Conformity and Regulatory Information B-1 Vii Viii Audience PrefacePurpose OrganizationConventions Preface Conventions Related Publications SN Aaannnnxxxx Locating the Product Serial NumberXiv Lightweight Access Points Autonomous Access PointsOverview Product TerminologyGuidelines for Using 1130AG Series Lightweight Access Points Access Point Hardware Features Hardware FeaturesSingle or Dual-Radio Operation Power Sources Anti-Theft Features Access Point Security Screw Hole Network Examples with Autonomous Access PointsAccess point Root Unit on a Wired LANAccess Point as Repeater Repeater Unit that Extends Wireless RangeWorkgroup Bridge Configuration Central Unit in an All-Wireless NetworkNetwork Example with Lightweight Access Points OL-8369-05 Installing the Access Point General Safety Guidelines Safety InformationFCC Safety Compliance Statement Package Contents Unpacking the Access PointController Discovery Process for Lightweight Access Points Basic Installation GuidelinesDeploying the Access Points on the Wireless Network 1identifies the main access point hardware features Access Point Layout and ConnectorsMounting Plate Suspended Ceiling Adjustable T-Rail Clips Rail Clip Features Push here to open Push here to close Opening the Access Point Cover Opening the Access Point CoverMounting the Access Point on a Horizontal Surface Adjustable T-Rail Clips Mounting the Access Point Below a Suspended CeilingMounting the Access Point Above a Suspended Ceiling T-Bar Grid Mounting Bracket Parts Attaching the Access Point to the Mounting Plate Mounting Access Point on a Network Cable BoxMounting Access Point on a Desktop or Shelf 10 Aligning the Keyhole Clip to the Access Point Keyhole Using a Security Cable Securing the Access Point12 Installing the Security Hasp Adapter Securing the Access Point to the Mounting PlatePadlock Option Connecting the Ethernet and Power Cables15 Looping the Ethernet Cable Connecting to an Ethernet Network with Local Power 16 Cisco Logo Holes Rotating the Cisco LogoTroubleshooting Autonomous Access Points Status LED Ethernet LED Access point cover Radio LED Checking the Autonomous Access Point LEDsLow Power Condition for Autonomous Default Ssid and Radio Behavior Checking Basic SettingsDefault IP Address Behavior WEP Keys Enable Radio InterfacesSecurity Settings Intelligent Power Management Low Power Condition for Autonomous Access PointsInline Power Status Messages OL-8369-05 Page Configuring Power Using the CLI Issuing the Cisco IOS Command Using the CLI Power Negotiation selected Power inline never3 Running the Carrier Busy Test Running the Ping Test Resetting to the Default ConfigurationUsing the Web Browser Interface Using the Mode ButtonClick Reset to Defaults Reloading the Access Point ImageBrowser Http Interface Web Browser InterfaceBrowser Tftp Interface Obtaining the Access Point Image FileConnecting to the Access Point Console Port Http//tftpd32.jounin.net Obtaining the Tftp Server SoftwareOL-8369-05 Troubleshooting Lightweight Access Points Using Dhcp Option Checking the Lightweight Access Point LEDsStatus LED Ethernet LED Access point cover Radio LED Cable Bay Area Low Power Condition for Lightweight Access Low Power Condition for Lightweight Access Points Config ap power injector enable ap switch port MAC address Configuring Power Using Controller CLI CommandsConfig ap power pre-standard enable Power inline auto Configuring Controller Information Returning the Access Point to Autonomous ModeManually Resetting the Access Point to Defaults Clearing Manually Entered Controller InformationOL-8369-05 Mode Button Setting Obtaining the Autonomous Access Point Image FileConnecting to the Access Point Console Port Obtaining the Tftp Server Software OL-8369-05 Translated Safety Warnings OL-8369-05 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Canadian Compliance Statement Industry CanadaPage EMC Declaration of Conformity for RF Exposure Japanese Translation English Translation Chinese Translation English Translation Access Points with Ieee 802.11a RadiosAll Access Points Declaration of Conformity Statements Declaration of Conformity Annex to DofC# Information on Antennas and Power Levels OL-8369-05 Access Point Specifications CCK OET-65C OL-8369-05 Channels and Maximum Power Levels OL-8369-05 Console Cable Pinouts Overview Console Port Signals and PinoutsPriming Lightweight Access Points Prior to Deployment OL-8369-05 Page OL-8369-05 Access Points Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 and 1500 Series Access Points Type + Length + Value O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2
Related manuals
Manual 14 pages 8.61 Kb Manual 10 pages 10.06 Kb

1130AG specifications

The Cisco Systems 1130AG access point is a robust networking device designed to provide reliable wireless connectivity in a variety of environments. Specifically engineered for both indoor and outdoor applications, the 1130AG is particularly well-suited for use in enterprise, education, and hospitality sectors, where seamless connectivity and coverage are essential.

One of the standout features of the 1130AG is its dual-band operation. It supports both the 2.4 GHz and 5 GHz frequency bands, allowing it to utilize various channels for optimal performance and reduced interference. This dual-band capability enables it to service more devices simultaneously, accommodating the growing demand for wireless connectivity in mobile computing and Internet of Things (IoT) applications.

The access point incorporates advanced technologies such as IEEE 802.11a/g standards, which ensure compatibility with a wide array of wireless clients, ensuring widespread accessibility. The 1130AG also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single Ethernet cable. This feature not only streamlines setup but also enhances flexibility, as access points can be installed in locations where power sources are limited.

Security is a paramount concern in wireless networking, and the Cisco 1130AG addresses this through robust security protocols. It supports WPA, WPA2, and other encryption standards, ensuring secure data transmission and protecting against unauthorized access. This is particularly important for organizations that handle sensitive information and require strict compliance with data protection regulations.

Another notable characteristic is the ability of the 1130AG to seamlessly integrate with Cisco's extensive range of network management tools such as Cisco Prime, allowing administrators to monitor and manage their wireless network effectively. This integration provides insights into network performance, user access patterns, and device health, enabling proactive management and troubleshooting.

Moreover, the access point's compact design and durability make it suitable for various deployment scenarios. Designed to withstand varying environmental conditions, the 1130AG can be installed in demanding settings without compromising reliability.

In conclusion, the Cisco Systems 1130AG access point embodies advanced features and technologies that cater to the needs of modern businesses. Its dual-band capabilities, strong security protocols, and ease of management, alongside its durable design, make it an essential component for creating a high-performing wireless network. Whether in office buildings, educational institutions, or hospitality venues, the 1130AG provides the performance and reliability necessary to support today’s connected world.
Top Page Image Contents