Cisco Systems 1130AG manual Connecting the Ethernet and Power Cables, Option

Page 47

Chapter 2 Installing the Access Point

Connecting the Ethernet and Power Cables

Connecting the Ethernet and Power Cables

The access point receives power through the Ethernet cable or an external power module. Figure 2-14shows the power options for the access point.

Figure 2-14 Access Point Power Options

Option 1

Option 2

 

Switch

Switch with

(without inline power)

inline power

 

 

Catalyst 2950

Catalyst 2950

 

Power injector

Power cord

Universal

power supply

Access Point

Option 4

121717

Warning This product must be connected to a Power over Ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353

The access point supports the following power sources:

•Power module

•Inline power:

–Cisco Aironet Power Injector (AIR-PWRINJ3 or AIR-PWRINJ-FIB)

–An inline power capable switch, such as the Cisco Catalyst 3550 PWR XL, 3560-48PS, 3570-48PS, 4500 with 802.3AF PoE module, or the 6500 with 802.3AF PoE module

–Other inline power switches supporting the IEEE 802.3af inline power standard

Note Some older switches and patch panels might not provide enough power to operate the access point. At power-up, if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition. The access point also activates a Status LED low power error indication and creates an error log entry (refer to the “Low Power Condition for Autonomous Access Points” section on page 3-6or the “Low Power Condition for Lightweight Access Points” section on page 4-6).

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

 

OL-8369-05

2-21

 

 

 

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Americas Headquarters Page N T E N T S Access Point Layout and Connectors Guidelines for Using 1130AG Series Lightweight Access Points Declarations of Conformity and Regulatory Information B-1 Vii Viii Organization PrefaceAudience PurposeConventions Preface Conventions Related Publications SN Aaannnnxxxx Locating the Product Serial NumberXiv Product Terminology Autonomous Access PointsLightweight Access Points OverviewGuidelines for Using 1130AG Series Lightweight Access Points Access Point Hardware Features Hardware FeaturesSingle or Dual-Radio Operation Power Sources Anti-Theft Features Access Point Security Screw Hole Network Examples with Autonomous Access PointsAccess point Root Unit on a Wired LANAccess Point as Repeater Repeater Unit that Extends Wireless RangeWorkgroup Bridge Configuration Central Unit in an All-Wireless NetworkNetwork Example with Lightweight Access Points OL-8369-05 Installing the Access Point General Safety Guidelines Safety InformationFCC Safety Compliance Statement Package Contents Unpacking the Access PointController Discovery Process for Lightweight Access Points Basic Installation GuidelinesDeploying the Access Points on the Wireless Network 1identifies the main access point hardware features Access Point Layout and ConnectorsMounting Plate Suspended Ceiling Adjustable T-Rail Clips Rail Clip Features Push here to open Push here to close Opening the Access Point Cover Opening the Access Point CoverMounting the Access Point on a Horizontal Surface Adjustable T-Rail Clips Mounting the Access Point Below a Suspended CeilingMounting the Access Point Above a Suspended Ceiling T-Bar Grid Mounting Bracket Parts Attaching the Access Point to the Mounting Plate Mounting Access Point on a Network Cable BoxMounting Access Point on a Desktop or Shelf 10 Aligning the Keyhole Clip to the Access Point Keyhole Using a Security Cable Securing the Access Point12 Installing the Security Hasp Adapter Securing the Access Point to the Mounting PlatePadlock Option Connecting the Ethernet and Power Cables15 Looping the Ethernet Cable Connecting to an Ethernet Network with Local Power 16 Cisco Logo Holes Rotating the Cisco LogoTroubleshooting Autonomous Access Points Status LED Ethernet LED Access point cover Radio LED Checking the Autonomous Access Point LEDsLow Power Condition for Autonomous Default Ssid and Radio Behavior Checking Basic SettingsDefault IP Address Behavior WEP Keys Enable Radio InterfacesSecurity Settings Intelligent Power Management Low Power Condition for Autonomous Access PointsInline Power Status Messages OL-8369-05 Page Configuring Power Using the CLI Issuing the Cisco IOS Command Using the CLI Power Negotiation selected Power inline never3 Running the Carrier Busy Test Running the Ping Test Resetting to the Default ConfigurationUsing the Web Browser Interface Using the Mode ButtonClick Reset to Defaults Reloading the Access Point ImageBrowser Http Interface Web Browser InterfaceBrowser Tftp Interface Obtaining the Access Point Image FileConnecting to the Access Point Console Port Http//tftpd32.jounin.net Obtaining the Tftp Server SoftwareOL-8369-05 Troubleshooting Lightweight Access Points Using Dhcp Option Checking the Lightweight Access Point LEDsStatus LED Ethernet LED Access point cover Radio LED Cable Bay Area Low Power Condition for Lightweight Access Low Power Condition for Lightweight Access Points Config ap power injector enable ap switch port MAC address Configuring Power Using Controller CLI CommandsConfig ap power pre-standard enable Power inline auto Clearing Manually Entered Controller Information Returning the Access Point to Autonomous ModeConfiguring Controller Information Manually Resetting the Access Point to DefaultsOL-8369-05 Mode Button Setting Obtaining the Autonomous Access Point Image FileConnecting to the Access Point Console Port Obtaining the Tftp Server Software OL-8369-05 Translated Safety Warnings OL-8369-05 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Canadian Compliance Statement Industry CanadaPage EMC Declaration of Conformity for RF Exposure Japanese Translation English Translation Chinese Translation English Translation Access Points with Ieee 802.11a RadiosAll Access Points Declaration of Conformity Statements Declaration of Conformity Annex to DofC# Information on Antennas and Power Levels OL-8369-05 Access Point Specifications CCK OET-65C OL-8369-05 Channels and Maximum Power Levels OL-8369-05 Console Cable Pinouts Overview Console Port Signals and PinoutsPriming Lightweight Access Points Prior to Deployment OL-8369-05 Page OL-8369-05 Access Points Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 and 1500 Series Access Points Type + Length + Value O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2
Related manuals
Manual 14 pages 8.61 Kb Manual 10 pages 10.06 Kb

1130AG specifications

The Cisco Systems 1130AG access point is a robust networking device designed to provide reliable wireless connectivity in a variety of environments. Specifically engineered for both indoor and outdoor applications, the 1130AG is particularly well-suited for use in enterprise, education, and hospitality sectors, where seamless connectivity and coverage are essential.

One of the standout features of the 1130AG is its dual-band operation. It supports both the 2.4 GHz and 5 GHz frequency bands, allowing it to utilize various channels for optimal performance and reduced interference. This dual-band capability enables it to service more devices simultaneously, accommodating the growing demand for wireless connectivity in mobile computing and Internet of Things (IoT) applications.

The access point incorporates advanced technologies such as IEEE 802.11a/g standards, which ensure compatibility with a wide array of wireless clients, ensuring widespread accessibility. The 1130AG also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single Ethernet cable. This feature not only streamlines setup but also enhances flexibility, as access points can be installed in locations where power sources are limited.

Security is a paramount concern in wireless networking, and the Cisco 1130AG addresses this through robust security protocols. It supports WPA, WPA2, and other encryption standards, ensuring secure data transmission and protecting against unauthorized access. This is particularly important for organizations that handle sensitive information and require strict compliance with data protection regulations.

Another notable characteristic is the ability of the 1130AG to seamlessly integrate with Cisco's extensive range of network management tools such as Cisco Prime, allowing administrators to monitor and manage their wireless network effectively. This integration provides insights into network performance, user access patterns, and device health, enabling proactive management and troubleshooting.

Moreover, the access point's compact design and durability make it suitable for various deployment scenarios. Designed to withstand varying environmental conditions, the 1130AG can be installed in demanding settings without compromising reliability.

In conclusion, the Cisco Systems 1130AG access point embodies advanced features and technologies that cater to the needs of modern businesses. Its dual-band capabilities, strong security protocols, and ease of management, alongside its durable design, make it an essential component for creating a high-performing wireless network. Whether in office buildings, educational institutions, or hospitality venues, the 1130AG provides the performance and reliability necessary to support today’s connected world.
Top Page Image Contents