Cisco Systems 1130AG manual OL-8369-05

Page 58

Chapter 3 Troubleshooting Autonomous Access Points

Low Power Condition for Autonomous Access Points

•%CDP_PD-4-POWER_OK: Full Power - INJECTOR_DETECTED_PD inline power source—This message indicates the access point is operating at full power because it has detected a CDP packet from another Cisco powerable device (PD). The access point power is being supplied from a power injector or a non-Cisco power source because a Cisco power source does not transmit this type of CDP packet.

•%CDP_PD-4-POWER_OK: Full Power - INJECTOR_DETECTED_MULTIPLE_MACS_ON_ HUB inline power source—This message indicates the access point is operating at full power because it has detected multiple Cisco devices. The access point power is being supplied from a power injector or a non-Cisco power source because a Cisco power source does not forward CDP packets.

•%CDP_PD-4-POWER_OK: Full Power - NON_CISCO-NO_CDP_RECEIVED inline power source—This message indicates the access point is operating at full power because it has not received any CDP packets within the timeout period. This condition indicates your access point is connected to a non-Cisco power source.

Note To prevent possible over-current conditions, the power source must be an IEEE 802.3af compliant power source or an IEC60950 compliant limited power source.

•%CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED inline power source—This message indicates the access point is in low power mode with all radios disabled because the Cisco power source has indicated it is not capable of supplying sufficient power to the access point.

Note A Cisco power injector might be required.

•%CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_ CONFIGURED <platform name> (<MAC address>)—This message indicates the access point is in low power mode with all radios disabled and has detected a CDP device that is unable to supply sufficient power to the access point.

The< platform name> indicates the CDP device detected by the access point. The <MAC address> indicates the MAC address of the CDP device, typically, the switch port.

Note A Cisco power injector might be required.

Following the low power status message, two extra messages are displayed on the console port or when using a Telnet session that identify the actions needed to resolve this low power problem:

–Verify the required power injector is installed on this port: <platform name> (<Ethernet port>).

(where <platform name> indicates the CDP device detected by the access point and <Ethernet port> indicates the Ethernet port of the CDP device.

–If a power injector is installed, issue the command: power inline negotiation injector installed.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3-8

OL-8369-05

 

 

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Americas Headquarters Page N T E N T S Access Point Layout and Connectors Guidelines for Using 1130AG Series Lightweight Access Points Declarations of Conformity and Regulatory Information B-1 Vii Viii Purpose PrefaceAudience OrganizationConventions Preface Conventions Related Publications Locating the Product Serial Number SN AaannnnxxxxXiv Overview Autonomous Access PointsLightweight Access Points Product TerminologyGuidelines for Using 1130AG Series Lightweight Access Points Hardware Features Access Point Hardware FeaturesSingle or Dual-Radio Operation Power Sources Anti-Theft Features Network Examples with Autonomous Access Points Access Point Security Screw HoleRoot Unit on a Wired LAN Access pointRepeater Unit that Extends Wireless Range Access Point as RepeaterCentral Unit in an All-Wireless Network Workgroup Bridge ConfigurationNetwork Example with Lightweight Access Points OL-8369-05 Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Unpacking the Access Point Package ContentsBasic Installation Guidelines Controller Discovery Process for Lightweight Access PointsDeploying the Access Points on the Wireless Network Access Point Layout and Connectors 1identifies the main access point hardware featuresMounting Plate Suspended Ceiling Adjustable T-Rail Clips Rail Clip Features Push here to open Push here to close Opening the Access Point Cover Opening the Access Point CoverMounting the Access Point on a Horizontal Surface Mounting the Access Point Below a Suspended Ceiling Adjustable T-Rail ClipsMounting the Access Point Above a Suspended Ceiling T-Bar Grid Mounting Bracket Parts Mounting Access Point on a Desktop or Shelf Mounting Access Point on a Network Cable BoxAttaching the Access Point to the Mounting Plate 10 Aligning the Keyhole Clip to the Access Point Keyhole Securing the Access Point Using a Security CableSecuring the Access Point to the Mounting Plate 12 Installing the Security Hasp AdapterPadlock Connecting the Ethernet and Power Cables Option15 Looping the Ethernet Cable Connecting to an Ethernet Network with Local Power Rotating the Cisco Logo 16 Cisco Logo HolesTroubleshooting Autonomous Access Points Checking the Autonomous Access Point LEDs Status LED Ethernet LED Access point cover Radio LEDLow Power Condition for Autonomous Default IP Address Behavior Checking Basic SettingsDefault Ssid and Radio Behavior Security Settings Enable Radio InterfacesWEP Keys Low Power Condition for Autonomous Access Points Intelligent Power ManagementInline Power Status Messages OL-8369-05 Page Configuring Power Using the CLI Issuing the Cisco IOS Command Using the CLI Power Negotiation selected Power inline never3 Running the Carrier Busy Test Resetting to the Default Configuration Running the Ping TestUsing the Mode Button Using the Web Browser InterfaceReloading the Access Point Image Click Reset to DefaultsWeb Browser Interface Browser Http InterfaceObtaining the Access Point Image File Browser Tftp InterfaceConnecting to the Access Point Console Port Obtaining the Tftp Server Software Http//tftpd32.jounin.netOL-8369-05 Troubleshooting Lightweight Access Points Checking the Lightweight Access Point LEDs Using Dhcp OptionStatus LED Ethernet LED Access point cover Radio LED Cable Bay Area Low Power Condition for Lightweight Access Low Power Condition for Lightweight Access Points Configuring Power Using Controller CLI Commands Config ap power injector enable ap switch port MAC addressConfig ap power pre-standard enable Power inline auto Manually Resetting the Access Point to Defaults Returning the Access Point to Autonomous ModeConfiguring Controller Information Clearing Manually Entered Controller InformationOL-8369-05 Obtaining the Autonomous Access Point Image File Mode Button SettingConnecting to the Access Point Console Port Obtaining the Tftp Server Software OL-8369-05 Translated Safety Warnings OL-8369-05 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementPage EMC Declaration of Conformity for RF Exposure Japanese Translation English Translation Access Points with Ieee 802.11a Radios Chinese Translation English TranslationAll Access Points Declaration of Conformity Statements Declaration of Conformity Annex to DofC# Information on Antennas and Power Levels OL-8369-05 Access Point Specifications CCK OET-65C OL-8369-05 Channels and Maximum Power Levels OL-8369-05 Console Cable Pinouts Console Port Signals and Pinouts OverviewPriming Lightweight Access Points Prior to Deployment OL-8369-05 Page OL-8369-05 Access Points Access Point Vendor Class Identifier VCI Configuring Option 43 for 1000 and 1500 Series Access Points Type + Length + Value O S S a R Y GL-2 GL-3 GL-4 GL-5 GL-6 D E IN-2
Related manuals
Manual 14 pages 8.61 Kb Manual 10 pages 10.06 Kb

1130AG specifications

The Cisco Systems 1130AG access point is a robust networking device designed to provide reliable wireless connectivity in a variety of environments. Specifically engineered for both indoor and outdoor applications, the 1130AG is particularly well-suited for use in enterprise, education, and hospitality sectors, where seamless connectivity and coverage are essential.

One of the standout features of the 1130AG is its dual-band operation. It supports both the 2.4 GHz and 5 GHz frequency bands, allowing it to utilize various channels for optimal performance and reduced interference. This dual-band capability enables it to service more devices simultaneously, accommodating the growing demand for wireless connectivity in mobile computing and Internet of Things (IoT) applications.

The access point incorporates advanced technologies such as IEEE 802.11a/g standards, which ensure compatibility with a wide array of wireless clients, ensuring widespread accessibility. The 1130AG also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single Ethernet cable. This feature not only streamlines setup but also enhances flexibility, as access points can be installed in locations where power sources are limited.

Security is a paramount concern in wireless networking, and the Cisco 1130AG addresses this through robust security protocols. It supports WPA, WPA2, and other encryption standards, ensuring secure data transmission and protecting against unauthorized access. This is particularly important for organizations that handle sensitive information and require strict compliance with data protection regulations.

Another notable characteristic is the ability of the 1130AG to seamlessly integrate with Cisco's extensive range of network management tools such as Cisco Prime, allowing administrators to monitor and manage their wireless network effectively. This integration provides insights into network performance, user access patterns, and device health, enabling proactive management and troubleshooting.

Moreover, the access point's compact design and durability make it suitable for various deployment scenarios. Designed to withstand varying environmental conditions, the 1130AG can be installed in demanding settings without compromising reliability.

In conclusion, the Cisco Systems 1130AG access point embodies advanced features and technologies that cater to the needs of modern businesses. Its dual-band capabilities, strong security protocols, and ease of management, alongside its durable design, make it an essential component for creating a high-performing wireless network. Whether in office buildings, educational institutions, or hospitality venues, the 1130AG provides the performance and reliability necessary to support today’s connected world.
Top Page Image Contents