Cabletron Systems HSIM-FE6 manual Connecting to the Network

Page 31

Connecting to the Network

3.Verify that a link exists by checking that the port receive LED is on (flashing amber, blinking green, or solid green). If the receive LED is off, perform the following steps until it is on:

a.Verify that the 100BASE-TX device at the other end of the twisted pair segment is powered up.

b.Verify that the RJ45 connector on the twisted pair segment has the proper pinouts.

c.Check the cable for continuity.

d.Make sure that the twisted pair connection meets cable specifications outlined in Appendix B.

e.Confirm that the crossover switch is in the correct position.

If a link is not established, refer to Chapter 3, LANVIEW LEDs, for information before contacting the Cabletron Systems Global Call Center. Refer to Section 1.5 for details.

HSIM-FE6 User’s Guide

2-13

Page 30 Page 32
Image 31
Page 30 Page 32
Contents HSIM-FE6 Page HSIM-FE6 User’s Guide Industry Canada Notice Cabletron Software Program License HSIM-FE6 User’s Guide Declaration of Conformity HSIM-FE6 User’s Guide Contents Contents Viii HSIM-FE6 User’s Guide Figures Tables Chapter Introduction Using this ManualConnectivity Full Duplex Switched EthernetLanview Diagnostic LEDs OverviewDocument Conventions Fepim OptionsYour email address Getting HelpRelated Documentation HSIM-FE6 User’s Guide Unpacking the HSIM-FE6 Chapter InstallationInstalling Fast Ethernet Port Interface Modules Installing Fast Ethernet Port Interface Modules Installing the Fepim Installing the HSIM-FE6 in an Interface Module Installing the HSIM-FE6Removing the Hsim Coverplate Installing the HSIM-FE6 Installing the HSIM-FE6 in a Standalone Device Connecting to the Network Connecting a Fiber Optic Segment to the Fepim FE-100TX Crossover Switch Connecting a Twisted Pair Segment to the FE-100TXStraight-Through Cable Connecting to the Network HSIM-FE6 User’s Guide HSIM-FE6 LEDs ChapterLanview LEDs FE-100TX LEDHSIM-FE6 Local Management HSIM-FE6 Local ManagementHSIM-FE6 User’s Guide Physical Properties Appendix a SpecificationsEnvironmental Requirements Regulatory Compliance FE-100TX Appendix B Fepim SpecificationsFE-100FX Figure B-2 FE-100FX Table B-1 Transmitter PowerFE-100F3 HSIM-FE6 User’s Guide

HSIM-FE6 specifications

Cabletron Systems HSIM-FE6 is a high-performance network interface card designed for use in the Cabletron Systems network equipment line, notably in the company's modular switching and routing platforms. This card is particularly known for its versatility and efficiency in managing network traffic in both enterprise environments and service provider networks.

One of the standout features of the HSIM-FE6 is its support for six 10/100 Mbps Fast Ethernet ports. This enables the card to provide high-speed connectivity for multiple devices, accommodating the growing demands for bandwidth in wired networks. The ability to automatically negotiate speeds ensures that connected devices can optimize their performance based on their capabilities, which is particularly beneficial in mixed-technology environments.

The HSIM-FE6 also employs advanced traffic management technologies, including Quality of Service (QoS) capabilities. This allows network administrators to prioritize different types of traffic, ensuring that critical applications receive the bandwidth they need while reducing latency for time-sensitive data. The card supports various QoS features such as traffic shaping and class-of-service (CoS) tagging, enhancing overall network performance.

In terms of reliability, the HSIM-FE6 includes features such as error detection and correction mechanisms, helping to minimize data loss and integrity issues. The card’s design also emphasizes redundancy and failover capabilities, allowing for seamless communication even during hardware or network disruptions. This is essential for organizations that require high availability and minimal downtime.

Moreover, Cabletron’s HSIM-FE6 integrates easily with existing network infrastructures through its compatibility with popular networking protocols including Ethernet, TCP/IP, and others. The installation process is streamlined, making it accessible for less experienced network administrators while still providing advanced configurations for seasoned experts.

In summary, Cabletron Systems HSIM-FE6 is a robust networking solution that combines flexibility, speed, and reliability. Its six Fast Ethernet ports, advanced QoS features, and emphasis on fault tolerance make it an ideal choice for organizations looking to enhance their network capabilities. For both enterprise and service provider settings, the HSIM-FE6 stands as a testament to the progressive design principles inherent in Cabletron’s product line, continuing to meet the demands of modern network environments.
Top Page Image Contents