Cabletron Systems HSIM-FE6 manual Connecting a Twisted Pair Segment to the FE-100TX

Page 29

Connecting to the Network

4.Verify that a link exists by checking that the port receive LED is ON (flashing amber, blinking green, or solid green). If the receive LED is OFF and the transmit LED is not blinking amber, perform the following steps until it is ON:

a.Check that the power is turned on for the device at the other end of the link.

b.Verify proper crossover of fiber strands between the port on the HSIM-FE6 and the fiber optic device at the other end of the fiber optic link segment.

c.Verify that the fiber connection meets the dB loss specifications outlined in Appendix B.

If a link has not been established, refer to Chapter 3, LANVIEW LEDs, before contacting the Cabletron Systems Global Call Center. Refer to Section 1.5 for details.

2.4.2Connecting a Twisted Pair Segment to the FE-100TX

An FE-100TX has an internal crossover switch. When connecting a workstation, use a straight-through cable and set the FEPIM crossover switch shown in Figure 2-5to the crossed over position marked with X. When connecting networking devices, such as another bridge, repeater, or router, use a straight-through cable and set the FEPIM crossover switch shown in Figure 2-5to the straight-through position, marked with =.

Position X (crossed over)

1.RX+ 5. NC

2.RX- 6. TX-

3.TX+ 7. NC

4.NC 8. NC

x

=

10

100

FE-100TX

Position =

(not crossed over)

1.TX+ 5. NC

2.TX- 6. RX-

3.RX+ 7. NC

4.NC 8. NC

fecrossover

Figure 2-5 FE-100TX Crossover Switch

HSIM-FE6 User’s Guide

2-11

Page 28 Page 30
Image 29
Page 28 Page 30
Contents HSIM-FE6 Page HSIM-FE6 User’s Guide Industry Canada Notice Cabletron Software Program License HSIM-FE6 User’s Guide Declaration of Conformity HSIM-FE6 User’s Guide Contents Contents Viii HSIM-FE6 User’s Guide Figures Tables Chapter Introduction Using this ManualLanview Diagnostic LEDs Full Duplex Switched EthernetOverview ConnectivityDocument Conventions Fepim OptionsYour email address Getting HelpRelated Documentation HSIM-FE6 User’s Guide Unpacking the HSIM-FE6 Chapter InstallationInstalling Fast Ethernet Port Interface Modules Installing Fast Ethernet Port Interface Modules Installing the Fepim Installing the HSIM-FE6 in an Interface Module Installing the HSIM-FE6Removing the Hsim Coverplate Installing the HSIM-FE6 Installing the HSIM-FE6 in a Standalone Device Connecting to the Network Connecting a Fiber Optic Segment to the Fepim FE-100TX Crossover Switch Connecting a Twisted Pair Segment to the FE-100TXStraight-Through Cable Connecting to the Network HSIM-FE6 User’s Guide HSIM-FE6 LEDs ChapterLanview LEDs FE-100TX LEDHSIM-FE6 Local Management HSIM-FE6 Local ManagementHSIM-FE6 User’s Guide Environmental Requirements Appendix a SpecificationsPhysical Properties Regulatory Compliance FE-100TX Appendix B Fepim SpecificationsFE-100FX Figure B-2 FE-100FX Table B-1 Transmitter PowerFE-100F3 HSIM-FE6 User’s Guide

HSIM-FE6 specifications

Cabletron Systems HSIM-FE6 is a high-performance network interface card designed for use in the Cabletron Systems network equipment line, notably in the company's modular switching and routing platforms. This card is particularly known for its versatility and efficiency in managing network traffic in both enterprise environments and service provider networks.

One of the standout features of the HSIM-FE6 is its support for six 10/100 Mbps Fast Ethernet ports. This enables the card to provide high-speed connectivity for multiple devices, accommodating the growing demands for bandwidth in wired networks. The ability to automatically negotiate speeds ensures that connected devices can optimize their performance based on their capabilities, which is particularly beneficial in mixed-technology environments.

The HSIM-FE6 also employs advanced traffic management technologies, including Quality of Service (QoS) capabilities. This allows network administrators to prioritize different types of traffic, ensuring that critical applications receive the bandwidth they need while reducing latency for time-sensitive data. The card supports various QoS features such as traffic shaping and class-of-service (CoS) tagging, enhancing overall network performance.

In terms of reliability, the HSIM-FE6 includes features such as error detection and correction mechanisms, helping to minimize data loss and integrity issues. The card’s design also emphasizes redundancy and failover capabilities, allowing for seamless communication even during hardware or network disruptions. This is essential for organizations that require high availability and minimal downtime.

Moreover, Cabletron’s HSIM-FE6 integrates easily with existing network infrastructures through its compatibility with popular networking protocols including Ethernet, TCP/IP, and others. The installation process is streamlined, making it accessible for less experienced network administrators while still providing advanced configurations for seasoned experts.

In summary, Cabletron Systems HSIM-FE6 is a robust networking solution that combines flexibility, speed, and reliability. Its six Fast Ethernet ports, advanced QoS features, and emphasis on fault tolerance make it an ideal choice for organizations looking to enhance their network capabilities. For both enterprise and service provider settings, the HSIM-FE6 stands as a testament to the progressive design principles inherent in Cabletron’s product line, continuing to meet the demands of modern network environments.
Top Page Image Contents