Cabletron Systems 3Com manual Select Easy Setup--Easy Setup, Parameter Description

Page 45

Installing the Access Point

45

Installing the Access AP Easy Setup is the program in which you set basic parameters for an AirConnect

Pointwireless network. These parameters include designating a gateway address that enables message forwarding across routers on the wired Ethernet.

To install an AP, follow the procedure below.

1Select Easy Setup-->Easy Setup.

The parameters in the Access Point Easy Setup window are explained in the list below.

Parameter

Description

 

 

Unit Name

AP name

IP Address

Network-assigned Internet Protocol address of the AP

Gateway IP Address

IP address of a router the AP uses on the Ethernet

 

default gateway

Subnet Mask

Consists of four sets of digits that help divide a

 

network into subnetworks and simplify routing and

 

data transmission

DHCP

Enable/Disable automatic IP address assignment by a

 

DHCP server

Help URL

URL of web management help file

Wireless LAN Service

WLAN service area identifier

Area

 

Diversity

Enables selection of antenna diversity. Choose

 

Primary Only

Additional Gateways

IP addresses of the additional gateways used. You can

 

access up to eight gateways

 

 

2Verify that the AP parameters reflect the network environment and change the parameters as needed.

3Do one of the following:

Click Save Settings to write changes if you make modifications.

Click Clear Entries to remove your changes and return the default settings.

Adding Additional You can add the IP addresses of additional gateways during Easy Setup. To do so, Gateways follow this procedure:

1Select Easy Setup-->Easy Setup.

2Click Add/Delete Gateways.

The Easy Setup - Add/Delete Gateways page displays.

3Enter the IP addresses of up to seven additional APs.

4Click Save Settings to write your changes.

5Click Clear Entries to remove your changes and return the default settings.

Image 45
Contents Version AirConnect 11 Mbps Wireless LAN Access Point User GuideBayfront Plaza Santa 3Com CorporationClara, California 95052-8145Contents Installing Access Point Hardware Monitoring Wireless Clients Access Point Installation Configuring the AP Access Point Specifications Technical Support Page Introduction Overview of Digital Wireless NetworkingAirConnect Network TopologiesOverview of Digital Wireless Networking AirConnect Network Topologies Wireless clients AirConnect AccessPoint To the Ethernet LANAirConnect Access Point Wireless clients and APs PowerBASE-TRadio Basics Results in the original digital dataRadio Basics 802.1d Spanning Tree Support Wireless LAN Service AreaSite Surveys Filtering and Access Control Network Control Protocol NCP as described PPP Connection Data Rate Requirement Overview of Digital Wireless Networking Theory of Operation Simple Network Management Protocol Snmp Programmable Snmp Trap Support Using SnmpManagement protocol MIB Increased MIB SupportMethod Description Using the User InterfacePrecautions Installing Access Point HardwarePackage Contents RequirementsStandard power supply 115/230VAC, 50/60Hz, 24V/14 Power OptionsRemote power distribution system, Part Number AP-PS-11 US line cord Part NumberMounting the AP BelowWall Mount To mount an AP on a wall Ceiling Mount To mount an AP on a ceiling Mounting the AP Using PowerBASE-TPowerBASE-T can be used to power the AP LED Indicators Off Blinking Power No power Power on During boot sequenceCondition, and other activity 3Com Support Center TroubleshootingVerify AP Operation Electrical Management System EMS operating outletNetwork connection verification Verify Network Wiring TopologyPage System Properties Monitoring StatisticsInterface Statistics Forwarding CountsEthernet Statistics Radio FrequencyStatistics Statistics window, select Main Menu→Misc Statistics MiscellaneousPress Esc or Previous F4 to exit Type Name DefinitionClearing Statistics Known APsSelect Clear All Statistics Gaining access to the User Interface UI Gaining Access to the User Interface UI Using a Web BrowserHelp File Access Setup Network Web Server Help File AccessSelect Virtual Directory Accessing the Web Browser UISelect Close/Exit Select System ConfigurationSelect Save F1 to save the configuration Select Special Functions Select Reset APType the case sensitive AP name Under Configuration, select Security Select System PasswordSelect Easy Setup--Easy Setup Select Easy Setup--Easy Setup Click Add/Delete GatewaysParameter Description Adding Allowed Wireless Clients Adding or Deleting a Range of Allowed Wireless ClientsAdding or Deleting Disallowed Wireless Clients Considerations For the Short RF Preamble setting, click DisabledEnabling or Disabling Encryption Select Configuration--SecurityEnable or disable interfaces on the AP Interface Description Default ConditionFrequency No. of Channels Country Enter the Multicast Mask data and voice values Snmp Trap Description Default Value Select Enabled or Disable All for All Snmp TrapsConfiguring the Originating Modem Configuring the Answering Modem Filtering to Forward PacketsFiltering to Discard Packets Click Delete Filter Removing Filtered Packet Types Networking ProtocolsDisabling Type Filtering Under Configuration, select FirmwareSpecial Function Description Active. Clear the wireless client association table forMonitoring Wireless Clients Wireless ClientsSelect Regular at the Wireless Clients prompt Indicates a 3Com voice-enabled device Ascii Interface Latest version. Refer to Manually Updating AP Firmware onVersions Enable serial port Configure the AP for the followingArrow/Function Key Control Character Prompt Description To exit from submenus, press EscPress Tab to select System Password Select Telnet LoginsTo enable and configure the serial port connection on the AP Configuring The Serial PortConfiguring the Dial-Up System Setting DescriptionHanging Up Select Modem HangupWindow InstallationConfiguring the AP That can associate with this AP. The default is Disabled Wsaid PPP Direct Establishing a ConnectionPPP with Modems Originating AP Set the Connect Mode to AnswerAnswering AP From the answering APs UIFor automatic dial-out, reset the AP Press up/down arrows to toggle between range and individual Range of Wireless ClientsRemoving Allowed Wireless Clients Enable/Disable the ACLRemoving All Allowed Wireless Clients Adding Disallowed Wireless Clients Load ACL from Wireless Client ListRemoving Disallowed Wireless Clients Address FilteringSetting Logging Clearing WirelessClients from the AP OptionsManually Updating AP FirmwarePrevious version of AP firmware Remainder of this procedure uses Windows 98 as an example Select Alter Filenames/HELP URL/TFTP and press EnterType the firmware file name in the Download Filename field Open the Special Functions window Select Transfer from the emulation program menu barSelect Send File Select Alter Filenames/HELP URL/TFTP Server and press Enter Download is complete when the UI displaysAuthentication Using MD5Performing Pings Extended RoamingWireless client and the access point EncryptionHex-digit sequence Restoring Configurations Press the Tab key to highlight .Short RF Preamble EnabledSelect Restore Factory Configuration Physical Characteristics Access Point SpecificationsRadio Characteristics Frequency No. of Channels Country Output CharacteristicsNetwork Characteristics Technical Support ServicesOnline Technical World Wide Web SiteNorth America Latin AmericaTo obtain an RMA number, call or fax Page Ascii IndexSnmp agent 3Com AirConnect Access Point 3Com Corporation Limited WarrantyObtaining Warranty Radio Frequency Interference Requirements Canada Regulatory Compliance Information3Com End User Software License Agreement Important Read Before Using This Product