Cabletron Systems 3Com Ascii Interface, Latest version. Refer to Manually Updating AP Firmware on

Page 57

6

CONFIGURING THE AP USING THE

ASCII INTERFACE

Introduction

Software configuration consists of setting up a connection to the Access Point (AP)

 

and gaining access to the User Interface (UI).

 

Before configuring the AP, you should upgrade the AirConnect firmware to the

 

latest version. Refer to “Manually Updating AP Firmware” on page 73.

 

The dot in front of certain parameters, functions, or options (.Antenna Selection

 

Primary Only) indicates these items update to all APs with the same WLAN

 

Service Area when you select the “Upgrade ALL APs” [F2] option. This option can

 

only be executed among the same hardware platforms and same firmware

 

versions.

 

In Windows 2000, the F1 key will not work correctly to save configuration

 

settings. To save settings, press the Tab key to highlight the onscreen F1

 

selection, then press Enter. Answer yes when prompted to save changes.

 

To enable the F1 key to work correctly in Windows 2000, you should upgrade

 

your Hyperterminal application to Hyperterminal Private Edition. This software is

 

available at http://www.hilgraeve.com/htpe/index.html.

Gaining Access to the The method for establishing access to the UI depends on the connection used.

User Interface (UI) Select the setup that best fits the network environment. Your connection options are:

Telnet

Direct serial connection

Dial-up connection

If using a PPP or serial connection, access the UI through a Telnet session.

Using Telnet Using a Telnet session to gain access to the UI requires that a remote station has a TCP/IP stack. The remote station can be on the wired or wireless LAN.

To access the AP from the workstation, follow the procedure below.

1From the DOS prompt, Telnet to the AP using its IP address:

Telnet xxx.xxx.xxx.xxx

2If desired, enter a password (case sensitive) when prompted. The default is password is comcomcom.

Image 57
Contents Version AirConnect 11 Mbps Wireless LAN Access Point User GuideBayfront Plaza Santa 3Com CorporationClara, California 95052-8145Contents Installing Access Point Hardware Monitoring Wireless Clients Access Point Installation Configuring the AP Access Point Specifications Technical Support Page Introduction Overview of Digital Wireless NetworkingAirConnect Network TopologiesOverview of Digital Wireless Networking AirConnect Network Topologies Wireless clients AirConnect AccessPoint To the Ethernet LANAirConnect Access Point Wireless clients and APs PowerBASE-TRadio Basics Results in the original digital dataRadio Basics 802.1d Spanning Tree Support Wireless LAN Service AreaSite Surveys Filtering and Access Control Network Control Protocol NCP as described PPP Connection Data Rate Requirement Overview of Digital Wireless Networking Theory of Operation Simple Network Management Protocol Snmp Programmable Snmp Trap Support Using SnmpManagement protocol MIB Increased MIB SupportMethod Description Using the User InterfacePrecautions Installing Access Point HardwarePackage Contents RequirementsStandard power supply 115/230VAC, 50/60Hz, 24V/14 Power OptionsRemote power distribution system, Part Number AP-PS-11 US line cord Part NumberMounting the AP BelowWall Mount To mount an AP on a wall Ceiling Mount To mount an AP on a ceiling Mounting the AP Using PowerBASE-TPowerBASE-T can be used to power the AP LED Indicators Off Blinking Power No power Power on During boot sequenceCondition, and other activity 3Com Support Center TroubleshootingVerify AP Operation Electrical Management System EMS operating outletNetwork connection verification Verify Network Wiring TopologyPage System Properties Monitoring StatisticsInterface Statistics Forwarding CountsEthernet Statistics Radio FrequencyStatistics Statistics window, select Main Menu→Misc Statistics MiscellaneousPress Esc or Previous F4 to exit Type Name DefinitionClearing Statistics Known APsSelect Clear All Statistics Gaining access to the User Interface UI Gaining Access to the User Interface UI Using a Web BrowserHelp File Access Setup Network Web Server Help File AccessSelect Virtual Directory Accessing the Web Browser UISelect Close/Exit Select System ConfigurationSelect Save F1 to save the configuration Select Special Functions Select Reset APType the case sensitive AP name Under Configuration, select Security Select System PasswordSelect Easy Setup--Easy Setup Select Easy Setup--Easy Setup Click Add/Delete GatewaysParameter Description Adding Allowed Wireless Clients Adding or Deleting a Range of Allowed Wireless ClientsAdding or Deleting Disallowed Wireless Clients Considerations For the Short RF Preamble setting, click DisabledEnabling or Disabling Encryption Select Configuration--SecurityEnable or disable interfaces on the AP Interface Description Default ConditionFrequency No. of Channels Country Enter the Multicast Mask data and voice values Snmp Trap Description Default Value Select Enabled or Disable All for All Snmp TrapsConfiguring the Originating Modem Configuring the Answering Modem Filtering to Forward PacketsFiltering to Discard Packets Click Delete Filter Removing Filtered Packet Types Networking ProtocolsDisabling Type Filtering Under Configuration, select FirmwareSpecial Function Description Active. Clear the wireless client association table forMonitoring Wireless Clients Wireless ClientsSelect Regular at the Wireless Clients prompt Indicates a 3Com voice-enabled device Ascii Interface Latest version. Refer to Manually Updating AP Firmware onVersions Enable serial port Configure the AP for the followingArrow/Function Key Control Character Prompt Description To exit from submenus, press EscPress Tab to select System Password Select Telnet LoginsTo enable and configure the serial port connection on the AP Configuring The Serial PortConfiguring the Dial-Up System Setting DescriptionHanging Up Select Modem HangupWindow InstallationConfiguring the AP That can associate with this AP. The default is Disabled Wsaid PPP Direct Establishing a ConnectionPPP with Modems Originating AP Set the Connect Mode to AnswerAnswering AP From the answering APs UIFor automatic dial-out, reset the AP Press up/down arrows to toggle between range and individual Range of Wireless ClientsRemoving Allowed Wireless Clients Enable/Disable the ACLRemoving All Allowed Wireless Clients Adding Disallowed Wireless Clients Load ACL from Wireless Client ListRemoving Disallowed Wireless Clients Address FilteringSetting Logging Clearing WirelessClients from the AP OptionsManually Updating AP FirmwarePrevious version of AP firmware Remainder of this procedure uses Windows 98 as an example Select Alter Filenames/HELP URL/TFTP and press EnterType the firmware file name in the Download Filename field Open the Special Functions window Select Transfer from the emulation program menu barSelect Send File Select Alter Filenames/HELP URL/TFTP Server and press Enter Download is complete when the UI displaysAuthentication Using MD5Performing Pings Extended RoamingWireless client and the access point EncryptionHex-digit sequence Restoring Configurations Press the Tab key to highlight .Short RF Preamble EnabledSelect Restore Factory Configuration Physical Characteristics Access Point SpecificationsRadio Characteristics Frequency No. of Channels Country Output CharacteristicsNetwork Characteristics Technical Support ServicesOnline Technical World Wide Web SiteNorth America Latin AmericaTo obtain an RMA number, call or fax Page Ascii IndexSnmp agent 3Com AirConnect Access Point 3Com Corporation Limited WarrantyObtaining Warranty Radio Frequency Interference Requirements Canada Regulatory Compliance Information3Com End User Software License Agreement Important Read Before Using This Product