Cabletron Systems SEHI100TX-22 manual RX+ TX+ Position = Not crossed over

Page 39

Connecting the SEHI to the Network

Position X (crossed over)

1. RX+

5. NC

2. RX-

6. TX-

3. TX+

7. NC

4. NC

8. NC

Position =

(not crossed over)

1. TX+

5.

NC

 

2. TX-

6.

RX-

 

3. RX+

7. NC

 

4. NC

8. NC

1511_11

Figure 5-2 EPIM-100TX Crossover Switch

Connect an EPIM-100TX to a twisted pair segment as follows:

1.Connect the twisted pair segment to the module by plugging the RJ45 connector on the twisted pair segment into the RJ45 port on the module. See Figure 5-2.

2.Plug the RJ45 connector at the other end of the twisted pair segment into the other device as appropriate.

3.Check that the LNK LED on the EPIM-100TX is on. If the LED is off, perform each of the following steps until it is on:

a.Check that the 100BASE-TX device at the other end of the twisted pair segment is powered up.

b.Verify that the RJ45 connector on the twisted pair segment has the proper pinouts.

c.Check the cable for continuity.

d.Check that the twisted pair connection meets the cable specifications outlined in Section 3.1.2.

e.Check that the crossover switch is in the correct position.

If a link is not established, contact Cabletron Systems Technical Support.

SEHI100TX User’s Guide

5-3

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Intelligent Stackable HUB USER’S Guide Page SEHI100TX User’s Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents SEHI100TX User’s Guide Vii Contents Viii SEHI100TX User’s Guide Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsYour email address Getting HelpRelated Manuals Sehi Overview Chapter Sehi Features and OptionsSehi Features and Options Sehi FeaturesStackable Capabilities Rack Mounting Capabilities Remote Network ManagementOptional Epims Chapter Installation Requirements Specifications Cable SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Specifications Multimode Fiber Optic Cable Specifications Network Cable Lengths Network Cable Lengths COM Port Requirements Network Port SpecificationsAgency Approvals Operating SpecificationsPower Supply Requirements Environmental RequirementsPhysical Specifications Unpacking the Sehi Chapter InstallationNvram Switch Location PRE-INSTALLATION CheckoutRackmount Installation Tabletop or Shelf InstallationAttaching the Strain-Relief Bracket Rackmount Installation Adequate clearance two inches on either side Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Installing an Epim Installing AN EpimSEHI100TX User’s Guide Chapter Connecting to the Network Connecting the Sehi to the NetworkConnecting to Network Ports Sehi Network Ports Connecting to an EPIM-100TXRX+ TX+ Position = Not crossed over EPIM-100FX or EPIM-100FMB Port Connecting to an EPIM-100FX or EPIM-100FMBTesting the Installation SEHI100TX User’s Guide Installation Test Chapter TroubleshootingUsing Lanview Using Lanview Epim 1 RCV LED Using the Reset ButtonSetting the Nvram Switch SEHI100TX User’s Guide Chapter Local Management Keyboard Conventions Function Keyboard ConventionsManagement Terminal Setup Console Cable Configuration Management Terminal Setup Parameters Sehi Local Management Accessing Local ManagementAccessing Local Management Feature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenManagement fields, excluding IP Address Editing the Community Name Field Configuration Configuration ScreenSetting the IP Address Setting the Subnet Mask Setting the Default Gateway Using the Port Enable OverrideExiting the Configuration Screen Trap Table Screen Trap Table Screen1 Configuring the Trap Table Snmp Tools Screen Exiting the Trap Table ScreenFollowing sections describe Snmp Tools screen fields Getting Individual OIDs Getting the Next OID Setting an OIDWalking Through OIDs Viewing Multiple OIDsExiting the Snmp Tools Screen Stepping Through OIDsCycling Through OIDs Repeating the Last OIDDevice Statistics Screen Device Statistics ScreenDisplays the number of errors received This command lets the user enable the selected port Using the Enable Port Command Using the Disable Port CommandSelecting the Appropriate Module/Port Exiting the Device Statistics Screen Setting the UPDATE-FREQency FieldAppendix a Epim Specifications Epim SpecificationsEPIM-100TX EPIM-100FX Figure A-3 EPIM-100FMB EPIM-100FMBSEHI100TX User’s Guide Appendix B Image File Download Using OID Strings Setting Unix Workstation AS Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics IndexIndex-2 SEHI100TX User’s Guide Power Supply Cord
Related manuals
Manual 58 pages 17.82 Kb

SEHI100TX-22 specifications

Cabletron Systems SEHI100TX-22 is a high-performance network interface card that has been designed for reliable data transfer in various networking environments. Ideal for both enterprise and small business applications, the SEHI100TX-22 delivers exceptional performance at a competitive price point.

One of the standout features of the SEHI100TX-22 is its support for 100Base-TX Ethernet standards, which enables high-speed data transmission at rates of up to 100 Mbps. This high throughput capacity makes it an excellent choice for organizations that require swift and efficient data handling, particularly in environments with heavy network traffic.

The card is equipped with two RJ-45 connectors, allowing it to support dual-port configurations. This dual-port setup enhances networking capabilities by enabling fault tolerance and load balancing, ensuring that the network remains operational even in the event of a failure. Moreover, it supports full-duplex operation, allowing for simultaneous bi-directional data transmission, further improving overall network efficiency and performance.

Another significant advantage of the SEHI100TX-22 is its compatibility with a wide range of operating systems and platforms, including Windows, Linux, and various UNIX variants. This versatility ensures that it can be seamlessly integrated into existing network infrastructures without the need for extensive configuration or modification.

In terms of installation and maintenance, the SEHI100TX-22 is user-friendly, thanks to its Plug and Play capability. This feature allows for easy installation; users can simply insert the card into an available PCI slot, and the operating system will automatically recognize and configure the device, minimizing downtime and simplifying the setup process.

Additionally, the SEHI100TX-22 incorporates advanced technologies like Auto-Negotiation, which automatically detects the speed and duplex capabilities of the connected device, thus optimizing the network performance. The card also features various onboard diagnostic LEDs, providing real-time feedback on connection status and data activity, which aids in troubleshooting and performance monitoring.

In summary, the Cabletron Systems SEHI100TX-22 offers a robust set of features that cater to the demands of modern network environments. With its high-speed capabilities, dual-port support, compatibility across multiple operating systems, and user-friendly installation process, it remains a solid choice for organizations looking to enhance their networking performance and reliability.
Top Page Image Contents