Extron electronic HSA 222C, HSA 200CE Installation Overview, Preparing the Routing Template

Page 9

Installation

Installation Overview

Install and set up the HSA surface access enclosures as follows:

1If you have an unprepared mounting template, prepare the template. See “Preparing the Routing Template” on the next page.

2If desired, install the optional RJ-45 to RJ-11 conversion kit(s) to replace one or more RJ-45 connectors with RJ-11 connectors. Refer to the appropriate RJ-45 to RJ-11 Conversion Kit manual, for either the HSA 200 models or the HSA 222 models.

3If desired, install the optional flexible conduit kit to replace the removable AC power cord. Refer to the Flexible Conduit Kit manual.

4Cut a hole in the surface where the enclosure will be installed and install the enclosure. The screw clamps secure the enclosure to the tabletop. See “Preparing the Table and Mounting the Enclosure” in this chapter.

5Run all cables necessary to support the AC power, RJ-45, and (for HSA 200 model only) video and audio connectors. Leave enough slack in the cables to connect them to the underside of the enclosure.

6Turn off all of the equipment to be connected. Ensure that the equipment connected to the RJ-45, video, and audio connectors are all turned off and disconnected from the power source.

7Connect the power, video, audio, and RJ-45 cables to the underside of the enclosure. See “Underside Features and Cabling Connections” in this chapter.

8On HSA 200SE and HSA 200CE models, set the gain switch.

9Connect and turn on the input and output devices.

10For HSA 200SE and HSA 200CE model installations, the picture should now appear and sound should be audible. If not, ensure that all devices are plugged in and receiving power. Check the cabling and gain setting, and make adjustments as needed.

11Peel the protective coating from the top surface.

Preparing the Routing Template

Extron offers a metal template for each HSA model. Appendix A lists the HSA 200 and HSA 222 template part numbers. Extron recommends using this template as a guide to cut the hole in the table where the HSA will be installed.

 

The metal routing template is reusable. Do not discard

 

this template when the installation is complete. Save it

 

for installing future HSA enclosures of the same size.

1.

Cut 1/2" x 4" strips of soft, finished lumber long enough to

 

span the distance between the desired installation location

 

on the mounting surface and the edges of the mounting

 

surface (figure 2-1).

 

Mounting

 

Surface

 

Edge

 

Minimum

 

4 Screws

 

Wood

 

Strips

 

Wood Strip

 

Height

 

4" / 10.2 cm

Mounting

Routing Template

 

Surface

 

Edge

 

 

Wood Thickness

 

0.5" / 1.3 cm

Figure 2-1 — Prepared mounting template assembly

These strips raise the routing template above the mounting surface to provide room for the router’s collar, protect the mounting surface, and extend the reach of the routing template so that it can be clamped to the edge of the surface.

2. Using four or more short wood screws, secure the

mounting template to the lumber strips.

 

Do not allow the wood screws to protrude through

CAUTION

 

the bottom of the wooden strips. Protruding screws

will mar the table when the template is used.

2-2

HSA 200/222 Series • Installation

HSA 200/222 Series • Installation

2-3

Page 8 Page 10
Image 9
Page 8 Page 10
Contents HSA 200S & HSA 200SE Precautions s Table of Contents Table of Contents, cont’d HSA 200/222 Series Surface Access ProductsOne IntroductionIntroduction About the Hideaway Surface Access ProductsAbout the Extender board line driver FeaturesAll models HSA 200CE and HSA 200SE models onlyInstallation Introduction HSA 200/222 Series Surface Access ProductsTwo Installation Installation OverviewPreparing the Routing Template Preparing the table with a router Installing the HSA enclosure all Installation, cont’dUnderside Features and Cabling Connections All HSA 200 models onlyHSA 200C and HSA 200S no Extender board only HSA 200CE and HSA 200SE Extender board only All HSA 200 and HSA 222 modelsPower connector wiring Front Panel Connectors14 Audio input connector plug Three Maintenance and ModificationsIf the image does not appear or there is no sound If the image is not displayed correctlyMaintenance and Modifications Removing and Replacing the EnclosureReplacing the Bezels While you Maintenance and Modifications, cont’dRemoving the front panel When the HSA 200 is upside-down, the latch may Ensure that AC power is disconnected beforeServicing the HSA unit Be ineffective. If the latch releases in this positionFront access panel removal HSA 222 models Replacing the gas lift, HSA 222 model Adjusting the Top PanelReference Information AAppendix aReference Information SpecificationsSurface cutout dimensions here before cutting a hole Reference Information, cont’dGeneral HSA 200C/HSA 200CE international circular models HSA Part NumbersTop Plate Dimensions AccessoriesReference Information, cont’d Included Parts Routing TemplatesPackaging for Shipment Appendix BPackaging for Shipment Figure B-4 HSA unit suspended in the foam Packaging for Shipment, cont’d
Related manuals
Manual 30 pages 34.8 Kb Manual 2 pages 51.61 Kb Manual 3 pages 41.03 Kb

HSA 200SE, HSA 200S, HSA 222C, HSA 222S, HSA 200C specifications

The Extron HSA 222S is a highly advanced audio amplifier designed specifically for professional audio applications. As part of Extron's extensive range of audio solutions, the HSA 222S stands out for its robust features, innovative technologies, and user-friendly design, making it an ideal choice for educational institutions, corporate environments, and other venues requiring high-quality audio performance.

One of the most notable features of the HSA 222S is its powerful amplification capabilities. This amplifier delivers 20 watts per channel at 4 ohms, ensuring that audio signals can be reproduced with clarity and authority, even in larger spaces. The HSA 222S is designed with high-efficiency Class D amplification, which not only provides optimal power usage but also ensures low heat generation during operation, resulting in reliable performance throughout extended use.

The HSA 222S incorporates Extron's proprietary technologies, including the patented audio routing system that allows users to easily manage multiple audio sources. This flexibility assists in creating dynamic soundscapes and supports various audio applications. The amplifier also features advanced DSP options, enabling users to adjust equalization and fine-tune audio settings for diverse environments. This capability is particularly beneficial in venues that host multiple types of events, requiring adaptability in audio management.

Connectivity is another key characteristic of the HSA 222S. It is equipped with a range of input options, including line-level and microphone inputs, allowing seamless integration into existing audio infrastructures. With its balanced and unbalanced inputs, the HSA 222S can connect to a variety of audio devices, ensuring compatibility with numerous sound systems and configurations.

In addition to its outstanding performance and flexibility, the HSA 222S is designed for simplicity of use. Its intuitive front panel controls and informative LED indicators provide users with real-time feedback on system status, enabling easy adjustments as needed. Furthermore, Extron's extensive support and resources ensure that integrators can implement and maintain the HSA 222S efficiently.

Overall, the Extron HSA 222S is a powerful audio amplifier that combines cutting-edge technologies, versatility, and ease of use. With its capability to deliver superior sound quality while adapting to various audio demands, it serves as an essential component in modern audio-visual installations.
Top Page Image Contents