Extron electronic manual FPC 5000 TCP/IP Properties screen

Page 25

To log on to the Matrix 12800, the FPC 5000’s IP address and Subnet Mask fields must be set to values that identify them as being on the same subnet as the Matrix 12800 BME 0. See Subnetting — A Primer at the end of this chapter.

•In general, you probably do not need to edit these fields if:

°the FPC is connected directly to the Matrix 12800 via a crossover cable or you have already successfully logged on to the Matrix 12800, either directly or via an Ethernet LAN, and

°no changes have been made to the FPC’s and the Matrix 12800’s IP addresses and subnet masks.

•In general, you may need to edit these fields if:

°the FPC is connected to the Matrix 12800 via an Ethernet LAN, and

°you have not already successfully logged on to the Matrix 12800.

5. Change the FPC’s IP address and Subnet Mask field as follows:

a. Touch the Touch to change FPC’s IP address/network config banner in the IP Connection screen (figure 3-5). The FPC 5000 TCP/IP Properties screen appears (figure 3-6).

Figure 3-6 — FPC 5000 TCP/IP Properties screen

On this screen, you can direct the FPC 5000 to obtain its IP address from a Dynamic Host Configuration Protocol (DHCP) server (if the network is DHCP capable), reenter the factory defaults, or directly enter an IP address and subnet mask value.

Before any of the of the FPC 5000 properties change, the OK button is grayed out (not available) and a Close button replaces the Cancel button. If you decide to dismiss the FPC 5000 TCP/IP screen without changing any properties, touch the Close button and proceed to step 6.

b. Consult with your network administrator to determine the IP address and subnet mask values or if the FPC should obtain its IP address from a DHCP server.

c. To manually enter FPC IP settings, see if the Specify an IP address radio button is selected (). To change the setting, use a pencil eraser or other small, soft, object to touch the Specify an IP address radio button.

FPC 5000 Front Panel Controller • Matrix 12800 Operation

3-5

Page 24 Page 26
Image 25
Page 24 Page 26
Contents FPC Matrix 12800 Switcher Front Panel ControllerConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolTable of Contents Table of Contents, cont’d One About the Front Panel Controller Introductiontroduction, cont’dFPC 5000 Front Panel Controller Introduction Computer About the Matrix 12800 SystemIntroduction, cont’d Definitions of Matrix Switcher TermsTwo Installation Overview FPCInstallationdandOperation,Operationcont’dUnpacking and Assembling the Front Panel Controller A properly supported FPC computer and panel Inserting the machine screws FPC Installation and Operation, cont’dRear Panel Connections Rack Mounting the FPC AssemblyConnecting the FPC directly to a switcher BME FPC 5000 Start-up screen RJ-45 connector pinout tables Cabling and RJ-45 connector wiring10 Front panel control and indicators Front Panel Features and OperationMatrix 12800 Operation Upgrading the Software12 Inserting the program CD into the CD tray FPC Installation and Operation, cont’d Three Matrix12800Operation,c t’d Using the keyboardsIntroduction Operating the Touch PanelUsing on-screen scroll boxes Using the keypadsStarting Up the Controller and Logging In and Out Matrix 12800 Operation, cont’dFPC 5000 TCP/IP Properties screen If you touch the OK button, the FPC computer will reboot Navigating the Screens Demo Mode7a FPC 5000 Startup screen and menu flowchart part 7b FPC 5000 Startup screen and menu flowchart part Screens User ScreensViewing ties View ties screens flowchart Not include any video planes Viewing inputs tied to a specified outputViewing all ties Viewing outputs tied to a specified inputMake Ties dual keypad screen Creating tiesCreating ties using the Make Ties dual keypad screen End of the sequence Creating ties using the Make Ties alternate view screenSave, recall, or delete a global preset Preset screens10 Preset screens flowchart Name a global or room preset Save, recall, or delete a room preset11 Mute screen Mute screen12 Dsvp screen Dsvp screenStatus screen Admin ScreensStatus screen, System area Status screen, BME area Remotes screen15 TCP/IP screen TCP/IP screenDate field Password fieldsTime GMT field Matrix Name fieldSubnet Mask field Mail screenFPC IP Address field Mail Server IP Address field Mail Server Password fieldMail Server E-Mail User Name field Mail Addressee fields17 Miscellaneous screen Miscellaneous screen18 File Manager screen files shown are for example only File Manager screenShow 8 14 button Function Keys screenAppears in the radio button when it is selected 20 I/O Physical Connectors screen Physical Connectors screenRe-Install FPC Software button Setup ScreensNaming inputs and outputs Calibrate TouchScreen button21 Delay screen Delay screen22 Audio screen Audio screenBlank button Reset screenExample Subnetting a PrimerMatrix 12800 Operation, cont’d Extron’s Warranty Extron Electronics, USA

FPC 5000 specifications

The Extron FPC 5000 is a sophisticated hardware platform designed to enhance the capabilities of AV systems in professional environments. As a part of Extron's long-standing commitment to delivering high-performance solutions for audio and video distribution, the FPC 5000 stands out due to its versatile design and extensive feature set.

One of the key characteristics of the FPC 5000 is its ability to handle a variety of AV signals. Supporting 4K video resolutions, it provides exceptional clarity and detail, making it suitable for modern presentations and meetings. The device's flexibility allows it to accommodate various video formats, ensuring compatibility with a wide range of AV equipment and media sources. This adaptability is critical for businesses seeking to integrate legacy systems with cutting-edge technology.

The FPC 5000 incorporates advanced processing technologies, including high-speed input and output channels that facilitate low-latency signal handling. This is particularly important in environments where real-time communication and interaction are essential, such as classrooms and conference rooms. With the inclusion of Extron's proprietary technologies, like the Vector Technology for image processing, users can expect optimized performance in image scaling and color management.

Moreover, the FPC 5000 is designed with ease of use in mind. Featuring an intuitive user interface and customizable control options, it simplifies the operation of complex AV systems. Users can easily manage settings through a web-based control platform, eliminating the need for additional software or complicated setups.

Another significant feature of the FPC 5000 is its networking capabilities. With built-in support for Extron's Global Configurator Plus and other control systems, integration into larger networked AV environments is seamless. This simplifies the management of multiple devices, allowing for centralized control and monitoring.

In terms of reliability, the Extron FPC 5000 undergoes rigorous testing to meet professional standards. Built to withstand the demands of an active AV environment, it demonstrates durability and consistent performance.

In summary, the Extron FPC 5000 is a powerful solution for modern AV applications. Its combination of high-resolution support, advanced signal processing, user-friendly interface, and robust networking capabilities makes it an ideal choice for businesses looking to upgrade their AV infrastructure. Whether for educational institutions, corporate settings, or large venues, the FPC 5000 delivers exceptional performance and reliability.
Top Page Image Contents