Extron electronic IPL T SF24 Four, Communication and Control, Firmware upgrades, 192.168.254.253

Page 18

Connection and Configuration, cont’d

4.Select Internet Protocol (TCP/IP) from the list and click on Properties. (If you are using Windows 2000, right click Local Area Connection and select Properties from the menu, then select Internet Protocol (TCP/IP) from the list and click on Properties again.) If Internet Protocol (TCP/IP) is not on the list, it must be added (installed). Refer to your Windows user’s manual or the online Help system for information on how to install the TCP/IP protocol.

5.Write down your current IP address and Subnet Mask below. If your PC is set to “Obtain an IP address automatically,” make a note of that, instead.

IP Address:

. . .

Subnet Mask:

. . .

6.Click on “Specify an IP address” or “Use the following IP address” (depending on your operating system), and leave the default gateway blank. Enter the following values:

IP address:

192.168.254.253

Subnet mask: 255.255.0.0

7.Save the changes and exit the Network setup. Reboot the PC, if required, for the changes to become effective.

8.Launch your Web browser (Netscape Navigator or Internet Explorer), and type “http://192.168.254.254/index.html” in the address box. The IPL T default Web page will be displayed. Refer to IPL T interface configuration, in this chapter, for information on configuring your unit.

9.After configuring your IPL T interface, repeat steps 3 and 4 and change your TCP/IP settings back to their original configuration.

Firmware upgrades

Firmware upgrades will become available periodically, as improvements are made to the versatility and functionality of the IPL T interface. These upgrades will be available for download from the Extron Web site. For information on upgrading the firmware, see Upgrading the firmware in chapter 4.

IPL T SF24 and SFI244

Chapter4Four

Communication and Control

Ports Overview

Communication with the Interface

Programmer’s Guide for the Telnet and Web Browser

Customization

A/V Device Control

Troubleshooting

3-8 IPL T SF24 and IPL T SFI244 • Connection and Configuration

Image 18

Contents IP Link Tools USAPrecautions Extron’s WarrantyFCC Class a Notice Quick Start Guide IPL T SF24 and SFI244 Under Desk Projector MountTable of Contents Table of Contents, cont’d One IntroductionIPL T SF24 and SFI244 About this Manual FeaturesIntroduction About the IPL T SF24 and SFI244 InterfacesTwo Installation and OperationEasily configured and controlled Introduction, cont’dIPL T SF24 and IPL T SFI244 Installation and Operation Installation and OperationInstallation Overview Mounting the IPL T InterfacePower Installation and Operation, cont’dRear Panel Features and Cabling Furniture or projector mountingEthernet/LAN Serial communicationFront panel indicators OperationIdentification Resetting the unit Connection and Configuration ThreeSerial connection Connection and Configuration, cont’dConnecting the Hardware Ethernet connectionIPL T interface configuration Configuring the HardwarePC configuration Flex I/O connectionConfiguring the IPL T using direct PC connection Arp -s 10.13.170.15 00-05-A6-00-0A-90Ping Four Connection and Configuration, cont’dFirmware upgrades Communication and ControlFlex I/O ports Communication and Control, cont’dPorts Overview Digital inputBidirectional serial control interface ports Digital outputAnalog input Communication with the Interface Accessing and using the Web server Logon and system statusEstablishing or changing system or port settings Web server10 Web server System Settings screen Controlling IR devices or sending IR commands SFI244 onlySetting and changing your passwords Communication and Control, cont’dEditing and adding e-mail alerts Upgrading the firmware Sending an e-mail alert through TelnetEsc 4 SM Managing filesIR Learning SFI244 only Creating a driver with the IR Learner softwareUsing the command/response table Programmer’s Guide for the Telnet and Web browserSymbol definitions Password information Copyright informationBidirectional Serial Data port 28 = Commands that may give E28 file not foundError responses Flex I/O Data portIP Setup Commands IR/Serial Data port SFI244 onlyFirmware Version/Part Number/Information Web Browser Specific File CommandsRe-map port designations MailServer side includes Reset ZAP/Erase CommandsCommunication and Control, cont’d Customization ControlQuery string Code examplesExample 26c Browser view 28a Html source code using a query string Href=index.html?cmd=W1*1*15*0irPlay/a 30b Browser viewURL encoding Reserved charactersUnsafe characters Custom Web pages Direct port access ports 2001 throughCommunication and Control, cont’d Device Control Telnet PortPort redirect TroubleshootingPower connections Data connectionsSpecifications, Part Numbers Accessories AAppendix aSpecifications Parts AppendixBBGlossary Included partsGlossary GlossaryGlossary, cont’d