Extron electronic SFI244 Series, IPL T SF24 user manual Specifications

Page 41

Specifications, Part Numbers, Accessories, cont’d

Specifications

Ethernet control interface

Connectors

1 RJ-45 male connector

Data rate

10/100Base-T, half/full duplex with

 

autodetect

Protocols

ARP, DHCP, ICMP (ping), TCP/IP,

 

Telnet, HTTP, SMTP

Default settings

Link speed and duplex level =

 

autodetected

 

IP address = 192.168.254.254,

 

subnet mask = 255.255.0.0,

 

default gateway = 0.0.0.0

 

DHCP = off

Serial control interface

Port number/type

 

IPL T SF24

2 RS-232/RS-422/RS-485 configurable

 

serial

IPL T SFI244

2 RS-232 only

Connectors

 

IPL T SF24

(2) 9-pin male D and

 

(1) 3.5 mm 10-pole captive screw

 

connector

IPL T SFI244

(1) 3.5 mm 5-pole captive screw connector

Baud rate and protocol

300 to 115200 baud

 

Default settings (adjustable): 9600, 8-bit,

 

1 stop bit, no parity

Pin configurations

 

Serial, 9-pin D

 

RS-232 (default)

2 = RX, 3 = TX, 5 = GND, 7 = RTS, 8 = CTS

RS-422

2 = RX-, 3 = TX-, 5 = GND, 7 = TX+, 8 =

 

RX+

RS-485

2&3 = data- and tie 2&3, 5 = GND,

 

7&8 = data+ and tie 7&8

Serial, 5-pole captive screw

COM1: pin 1 = TX, 2 = RX, 3 = GND

COM2: pin 4 = TX, 5 = RX, 3 = GND

Flex I/O control interface

Number/type

4 analog or digital (configurable)

Connectors

(1) 3.5 mm captive screw connectors,

 

5 pole

Digital inputs

 

Input voltage range

0-24VDC, clamped at +30VDC

Input impedance

28 kohms

Programmable pullup

2 kohms to +5VDC

Threshold low to high ....

Programmable range: 100 mV to 24VDC,

 

default = 2VDC

Threshold high to low ....

Programmable range: 100 mV to 24VDC,

 

default = 1VDC

Digital outputs

250 mA sink from 24VDC max.

Analog inputs

12 bit A/D, 0 to 24VDC

Pin configurations

1, 2, 3, 4 = digital I/Os 1, 2, 3, 4; 5 = GND

IR/serial (IR/S) control interface — IPL T SFI244 only

Output port number

4

 

Connectors

(1) 3.5 mm 8-pole captive screw connector

IR output carrier frequency

30 kHz to 1 MHz

Pin configurations

pins 1, 3, 5, 7

= S 1, S2,S 3,S 4

 

pins 2, 4, 6, 8

= GND

General

Power

100VAC to 240VAC, 50/60 Hz, 10 watts,

 

external, autoswitchable; to 12VDC, 1 A

 

power supply. Product requires 0.5 A.

 

Alternatively, the product can use power

 

supplied over LAN/Ethernet (802.3af,

 

class 2).

Temperature/humidity

Storage -40° to +158°F (-40° to +70°C) /

 

10% to 90%, non-condensing

 

Operating +32° to +122°F (0° to +50°C) /

 

10% to 90%, non-condensing

Rack mount

Yes, with optional 1U rack shelf, part

 

#60-190-01, or the VersaTools rack shelf,

 

part #60-190-20;

 

also under-furniture mountable with

 

optional brackets #70-212-01

 

or projector mountable with optional

 

brackets #70-217-01/70-077-04

Enclosure type

Metal

Enclosure dimensions

1.7" H x 4.3" W x 3.0" D

 

(1U high, quarter rack width)

 

4.3 cm H x 10.9 cm W x 7.6 cm D

 

(Depth excludes connectors.)

Product weight

0.7 lbs (0.3 kg)

Shipping weight

2 lbs (1 kg)

A-2

IPL T SF24, IPL T SFI244 • Specifications, Part #s, Accessories

IPL T SF24, IPL T SFI244 • Specifications, Part #s, Accessories

A-3

Page 40 Page 42
Image 41
Page 40 Page 42
Contents USA IP Link ToolsFCC Class a Notice PrecautionsExtron’s Warranty Under Desk Projector Mount Quick Start Guide IPL T SF24 and SFI244Table of Contents Table of Contents, cont’d IPL T SF24 and SFI244 OneIntroduction Introduction FeaturesAbout this Manual About the IPL T SF24 and SFI244 InterfacesEasily configured and controlled Installation and OperationTwo Introduction, cont’dInstallation Overview Installation and OperationIPL T SF24 and IPL T SFI244 Installation and Operation Mounting the IPL T InterfaceRear Panel Features and Cabling Installation and Operation, cont’dPower Furniture or projector mountingSerial communication Ethernet/LANIdentification Front panel indicatorsOperation Resetting the unit Three Connection and ConfigurationConnecting the Hardware Connection and Configuration, cont’dSerial connection Ethernet connectionPC configuration Configuring the HardwareIPL T interface configuration Flex I/O connectionPing Configuring the IPL T using direct PC connectionArp -s 10.13.170.15 00-05-A6-00-0A-90 Firmware upgrades Connection and Configuration, cont’dFour Communication and ControlPorts Overview Communication and Control, cont’dFlex I/O ports Digital inputAnalog input Bidirectional serial control interface portsDigital output Establishing or changing system or port settings Accessing and using the Web server Logon and system statusCommunication with the Interface Web serverControlling IR devices or sending IR commands SFI244 only 10 Web server System Settings screenEditing and adding e-mail alerts Setting and changing your passwordsCommunication and Control, cont’d Esc 4 SM Sending an e-mail alert through TelnetUpgrading the firmware Managing filesCreating a driver with the IR Learner software IR Learning SFI244 onlyProgrammer’s Guide for the Telnet and Web browser Using the command/response tableSymbol definitions Copyright information Password informationError responses 28 = Commands that may give E28 file not foundBidirectional Serial Data port Flex I/O Data portFirmware Version/Part Number/Information IP Setup CommandsIR/Serial Data port SFI244 only Re-map port designations File CommandsWeb Browser Specific MailCommunication and Control, cont’d Customization Reset ZAP/Erase CommandsServer side includes ControlExample Query stringCode examples 26c Browser view 28a Html source code using a query string 30b Browser view Href=index.html?cmd=W1*1*15*0irPlay/aUnsafe characters URL encodingReserved characters Communication and Control, cont’d Device Control Direct port access ports 2001 throughCustom Web pages Telnet PortPower connections TroubleshootingPort redirect Data connectionsAAppendix a Specifications, Part Numbers AccessoriesSpecifications Glossary AppendixBBParts Included partsGlossary GlossaryGlossary, cont’d
Top Page Image Contents