Extron electronic IPI 200, IPI 100 manual Intercom with amplifier, Mpa

Page 23

Intercom with amplifier

The MLC’s Audio Out 2-pole captive screw connector outputs a -10 dBV audio signal that can be routed to an MPA 152 or any external audio amplifier, then to speakers.

1.Cable the system as shown in the following diagram.

		MPA 152	CLASS 2 WIRING	OUTPUT
C	US	MPA 152	CLASS 2 WIRING
	LISTED		DO NOT GROUND			4/8
	LISTED		OR SHORT			4/8
	17TT		SPEAKER OUTPUTS!			OHMS
	AUDIO/VIDEO		SPEAKER OUTPUTS!
	APPARATUS		INPUTS	L	R
POWER			INPUTS	L	R
POWER					REMOTE
					REMOTE
12V	L	R	L	R		VOL/MUTE
3A MAX					10V	50mA

MPA 152

SI 3CT LP

Ceiling Speakers

C NO

POWER RELAY AUDIO OUT

LAN

IPI 201

2.Power on the equipment.

3.Make fine adjustments to output level using the Remote Line slider in the Advanced Settings part of the HelpDesk software. The external amplifier (the MPA 152 in this example) must be adjusted properly to avoid any audio signal clipping or audio distortion.

4.If desired, use the software to adjust to minimum levels the IPI’s speaker output.

IPI 100 and IPI 200 Series • Installation

2-9

Image 23

Contents Push to Talk MediaLink IP Intercom InterfacesSicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisFCC Class a Notice Page Table of Contents Table of Contents, cont’d IPI 100 and IPI 200 Series Table of Contents Iii Iv IPI 100 and IPI 200 Series Table of Contents Before you get Started OneIPI 101 AAP IPI 104 AAP IPI 201 Series IPI 204 Series Terms and symbols used in this manualPreface About this ManualAdditional reference material About the IP Intercom ModulesLED indicator to show when the room is being monitored FeaturesSecurity features UL Requirements System RequirementsPreface, cont’d Two InstalllationMLC 226 IP’s rear panel, as shown in the following figure InstalllationIPI 100 and IPI 200 Series Installation MLC 226 IP AAP or a mounting frame ConnectorMLC Audio Connection Installlation, cont’dSingle PC to panel Sample ApplicationsNetwork Multiple PCs to panelPanel-to-panel mode Server mode MPA Intercom with amplifierInstalllation, cont’d Operation ThreeIPI 100 and IPI 200 Series Operation Front Panel Features and OperationOperation Button Color Indication Button OperationPush to talk operation Indication lighting\⤀Operation Four Initial ConfigurationBefore you Begin Initial ConfigurationIPI 100 and IPI 200 Series Initial Configuration Advanced button name changes to Basic Setting the IP address using Global ConfiguratorAt its factory default IP address IPI 200 Series intercom unit must beIntercom unit’s embedded Web page is displayed Setting the IP address using embedded Web pagesOpen a Web browser on the local PC Return to the TCP/IP Properties dialog box on the PC Arp s IP address MAC address Setting the IP address using the ARP commandHelpDesk Software FiveIPI 100 and IPI 200 Series HelpDesk Software Installling the SoftwareHelpDesk Software Introduction to the SoftwareStarting the Program Log-in as User Log-in as a HelpDesk AdministratorHelpDesk Software, cont’d Use the drop-down menu to select the appropriate option Configuring the IP Intercom SystemBasic Configuration Using the Configuration UtilitySelect Manually by IP Address from the drop-down menu Importing a GC2/GCZ fileClick Import. a Windows Open dialog box opens Entering an IP address manualllyScanning the local subnet Configuring an IP device with the configuration utility Talk mode Start speaking. While Listen modeSelect an available group or All Intercoms Group announcementTo load a pre-recorded file Loading a pre-recorded .wav fileChanging the default .wav file for intercom events Calll forwarding Setting up a peer-to-peer networkAll HelpDesks must be linked to the Server PC None of the PCs can be set to Server ModeSetting up one PC as a server Server PC must be set to Server Mode HelpDesk Software, cont’d Specifications, Part Numbers Accessories Specifications IPI 100 Series Specifications, Part Numbers, AccessoriesIncluded parts Replacement Part number Accessories IPI 100 Series\⤀Accessories Part number Included Parts IPI 100 Series\⤀Specifications IPI 200 Series Specifications, Part Numbers, Accessories, cont’dExtron Lbs 0.2 kg Amplifiers, cable, miscelllany Part number Accessories IPI 200 Series\⤀Included Parts IPI 200 Series\⤀ Specifications, Part Numbers, Accessories, cont’d SIS Programming and Control AppendixBBIPI 100 and IPI 200 Series SIS Programming and Control SIS Programming and ControlHost-to-IPI Communications IPI-initiated MessagesError response references Password informationError responses Using the command/response table Commands and Reponses= Escape key hex 1B Use W instead of Esc for Web browsers Symbol definitions= On/off status 0 = off / disable 1 = on /enable Telnet Web BrowserX4! = X4 = X7! = = on, disable/lock the front panel+X20 Command/response table for SIS commandsX20 X1! Command Ascii Telnet\⤀ URL Encoded ResponseX1! C X1! X1! X1! X4 X1@ CN Ipn X1@ IpnX4 X1@ orX1* X3$ X1$ CI X1$ X6$ EB X2@ X6$,X1$ EB Bmd X6$,X1$ Pvl X5@ X3# CU IpuX4! CK X5@ orStream Files via Telnet or RS-232 Directory commandsIPI 100 and IPI 200 Series SIS Programming and Control B-15 File handling commandsStream Files via Port 0AE 1AEIPI 100 and IPI 200 Series SIS Programming and Control B-17 Reset zap\⤀/Erase CommandsSIS Programming and Control, cont’d Mounting AppendixCCIPI 100 and IPI 200 Series Mounting MountingMounting the IPI 100 Series Mounting the IPI 200 Series Mounting, cont’d IPI 100 and IPI 200 SeriesDAppendix D Button LabelsButton Label Generator software Installling or Replacing Button LabelsInstallling the Button-Label Generator software Button LabelsUsing the Button-Label Generator software Text Installling Button LabelsExtron Warranty Quick Installation Checklist

Related manuals

Manual 2 pages 44.12 Kb