Extron electronic MVX 48, MVX 88, MVX 44, MVX 84 manual Example 5 View ties by selecting outputs

Page 30

Operation, cont’d

Example 5: View ties by selecting outputs

The following steps show an example of viewing the video and audio, audio-only, and video-only ties in the current configuration by selecting various outputs. The example shows the front panel indications that result from your actions.

This example assumes that you have performed example 1, example 2, and example 3.

1.

Select both video and audio for viewing (figure 3-22).

Press the button to cycle through the selections.

I/O

The video LED lights when video is selected. VID

The audio LED lights when audio is selected. AUD

Figure 3-22 — Select video and audio

Ensure that no input button is selected before you select an output button. If an input button is selected, the indications will not be as described and you may inadvertently establish potential ties that could be created by pressing the Enter button.

If you do inadvertently establish a potential tie by selecting an input and output button, do not press the Enter button. Allow the 5-second timeout to deselect all input and output buttons.

2.

Press and release the Output 3 button (figure 3-23).

Press and release the Output 3 button.

OUTPUTS

1

 

 

2

3

 

 

4

5

 

6

 

7

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Output 3 LED lights to indicate that output 3 is selected and it is receiving video or video and audio. The source (or sources, if audio is broken away) is indicated by the Input LED(s).

The Output 1, Output 4, and Output 8 LEDs also light to indicate that they are receiving video from the indicated input. These unselected outputs may or not be receiving audio, you cannot tell from these indications.

INPUTS

5

The Input 5 LED lights to indicate that this input's video is tied to output 3 (and the other lit outputs).

The audio LED blinks to indicate that, for at least one tie, audio is routed from a different source or not tied at all (audio breakaway).

I/O

VID +dB

AUD - dB

Figure 3-23 — Select an output

3-14 MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Operation

Page 29 Page 31
Image 30
Page 29 Page 31
Contents VGA Matrix Switchers MVX 44 / 48 / 84 / 88 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolIf desired, connect MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Quick Start QS-1Connect up to 4 or 8 high Control system orQuick Start MVX Series VGA Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One About the Switchers MVX 44 / 48 / 84 / 88 VGA Matrix Switchers IntroductionIntroductiontroduction, cont’d Features Any input to any or all outputsIntroduction, cont’d Two Rack mounting the switcher Installationstallation, cont’dMounting the Switcher Furniture mounting the switcherVideo and audio input connections Side of the furniture, where the switcher will be locatedCabling and Rear Panel Views Fasten it in placeInstallation, cont’d Video and audio output connectionsPower connection Remote connectionInstallation, cont’d Three Operationeration, cont’d Front Panel Controls and IndicatorsMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation DefinitionsPower/audio/data LED and infrared sensor Input and output selection controls and indicatorsPower/data/audio LED Operation, cont’d Selection and audio/video controls and indicatorsAudio Setup button Control buttons and LEDsOn 4-output switchers, this button and LED stand alone Powering up the switcher OperationsCreating a set of ties Example 1 Create a set of video and audio ties Select video and audio for the tie figurePress and release the Input 5 button figure Select the outputs Press and release the Enter button figureExample 2 Add a video tie to a set of video and audio ties Select video only for the tie figurePress and release the Output 1 button figure Example 3 Remove a tie from a set of ties Select audio only for the tie figurePress and release the Output 4 button figure 15 Deselect the outputOut Viewing the configurationAudio breakaway Example 4 View ties by selecting an input19 Select an input Press and release the I/O button figureExample 5 View ties by selecting outputs Press and release the Output 3 button figure24 Deselect audio to view video ties only Using presets Example 6 Save a presetExample 7 Recall a preset Preset 2 PresetAdjusting input audio gain and attenuation Press and release the Input 1 button figureMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Example 8 Adjust the input audio gain = unlit, = blinking LED+2 dB Lit +dB or -dB LED indicates the gain + or attenuation34 Exit Audio Setup mode Resetting audio gain single inputResetting audio gain all inputs Setting the output audio levelPress and release the and buttons simultaneously figure Front panel security lockout Executive mode Clearing all ties and presetsResetting the system to factory defaults MemoryTroubleshooting Audio signalOptimizing the Audio Worksheets Worksheet example 1 System equipmentPodium monitor Conf. room Sound VCR system USP Worksheet example 2 Daily configuration 44 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration 45 Worksheet example 3 Test configurationOperation, cont’d Configuration worksheet Output destinationsOperation, cont’d Four RemoteOperation,cont’d Host-to-Switcher instructionsMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote Operation Simple Instruction Set ControlSwitcher-initiated messages Symbol definitions Switcher error responsesUsing the command/response table Remote Operation, cont’dCommand/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands cont’d Global presets View ties, gain, mutes, and presets Click File Properties Loading firmware using an SIS commandSettings Ascii Setup Depress the keyboard’s EscClick the Files of type drop box and select All files File figureUsing the software Matrix Switchers Control ProgramInstalling the software OverviewExtron Matrix Switchers Control Program window blank Sample program window complete Updating the firmware Open windowMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote Operation Windows buttons, drop boxes, and trash Windows menusFile menu 11 RGB Delay/Mute/Output-Volume Adjust window Tools menu13 Ties shown as lines 14 Ties shown as crosspoints Using Emulation mode 15 Emulation mode configurationUsing the help system Remote Operation, cont’d AAppendix a SpecificationsandandPartPartNumbers,Numberscont’d SpecificationsSync Specifications and Part Numbers, cont’d Audio outputPart Numbers MVX Series VGA switchersOptional accessories Included partsVGA to BNC cable assemblies Part Install kits PartCable assemblies Part Audio cable assemblies PartFCC Class a Notice Extron’s Warranty Asia JapanExtron Electronics, USA
Related manuals
Manual 70 pages 45.03 Kb

MVX 48, MVX 84, MVX 44, MVX 88 specifications

Extron Electronics is a prominent leader in high-quality AV technology solutions, renowned for its innovative product lines designed to address diverse connectivity and distribution needs. Among their array of offerings, the MVX series stands out, particularly the MVX 44, MVX 84, and MVX 88 models, which cater to various AV signal routing needs within educational institutions, corporate environments, and large spaces.

The Extron MVX 44 is a 4x4 matrix switcher designed for routing HDMI, VGA, and audio signals. One of its key features is its ability to deliver high-resolution video up to 1080p, making it ideal for modern multimedia presentations. The MVX 44 supports EDID management, ensures compatibility with a range of source devices, and features automatic switching capabilities. It also includes a user-friendly interface for seamless operation, allowing simultaneous switching of multiple input sources to multiple outputs.

Expanding on the capabilities of the MVX 44, the MVX 84 and MVX 88 models provide enhanced functionality with additional inputs and outputs. The MVX 84 offers support for up to 8 input sources and 4 output destinations, while the MVX 88 offers 8x8 routing of signals. Both models maintain superior video quality and high-performance signal processing, accommodating more extensive AV systems. They also share features such as HDCP compliance to secure content protection, ensuring that the highest quality video signals are transmitted without degradation.

Technologically advanced, these switchers incorporate Extron's exclusive technologies, such as the Advanced Color Processing for superior color fidelity and signal reliability. Additionally, the Series comes equipped with optional control and integration capabilities, enabling connection to various AV control systems for centralized management.

The Extron MVX series matrices are built with the robustness expected from Extron products, ensuring long-term reliability in demanding environments. The integration of state-of-the-art support for audio signals allows not only video but also audio distribution, making them versatile for any AV setup. In summary, with their rich feature set, impressive scalability, and superior video processing capabilities, the Extron MVX 44, MVX 84, and MVX 88 present compelling solutions for anyone looking to streamline AV signal management in professional setups.
Top Page Image Contents