Extron electronic MVX 88 Remote Operation, cont’d, Switcher error responses, Symbol definitions

Page 52

Remote Operation, cont’d

Switcher error responses

When the switcher receives an SIS command and determines that it is valid, it performs the command and sends a response to the host device. If the switcher is unable to perform the command because the command is invalid or contains invalid parameters, the switcher returns an error response to the host. The error response codes are:

E01 — Invalid input channel number (out of range)

E10 — Invalid command

E11 — Invalid preset number (out of range)

E12 — Invalid output number (out of range)

E13 — Invalid value (out of range)

E14 — Invalid command for this configuration

Using the command/response table

The command/response table begins on page 4-5. Symbols used in the table represent variables in the command/response fields. Command and response examples are shown throughout the table. The ASCII to HEX conversion table at right is for use with the command/response table.

ASCII to HEX Conversion Table

Space

Symbol definitions:

= Carriage return/line feed

Esc = Escape key

X1 = Input number

X2 = Input number (for tie)

X3 = Output number

With the exception of the audio input gain and attenuation commands, the SIS commands are not case sensitive.

= Carriage return (no line feed)

•

= space

1 through 4 (MVX 44, MVX 48) or 1 through 8 (MVX 84, MVX 88)

0 (untie) – maximum number of inputs

1 through 4 (MVX 44, MVX 84) or 1 through 8 (MVX 48, MVX 88)

Input and output numbers in commands may be entered as either 1-digit, 2-digit, or 3-digit numbers. All input and output numbers are reported as 1-digit numbers in the response.

X4

X5

X6

X7

X8

X9

X10

X11

X12

= Numeric dB value

–18 to +10 (29 steps [dB] of audio attenuation and gain)

= Input audio gain

0 through 10 (1 dB/step)

 

 

= Input audio attenuation

1 through 18 (1 dB/step)

 

 

= Video/audio mute

0

= no mutes

2

= audio mute

 

1

= video mute

3

= video and audio mute

= Executive mode, mute

1

= on

0

= off

= Output gain

0 = consumer level (–10 dBV)

1

= pro level (+4 dBu)

= Preset number

01 through 16

 

 

See the note about leading zeros in preset numbers on page 4-7.

=Controller firmware version number to second decimal place

=RGB delay in ½ second increments (10 [5 seconds] maximum)

4-4 MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Remote Operation

Page 51 Page 53
Image 52
Page 51 Page 53
Contents VGA Matrix Switchers MVX 44 / 48 / 84 / 88 SeriesSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Quick Start QS-1 Connect up to 4 or 8 highIf desired, connect Control system orQuick Start MVX Series VGA Matrix Switchers, cont’d Table of Contents Table of Contents, cont’d One MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Introduction About the SwitchersIntroductiontroduction, cont’d Features Any input to any or all outputsIntroduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherRack mounting the switcher Furniture mounting the switcherSide of the furniture, where the switcher will be located Cabling and Rear Panel ViewsVideo and audio input connections Fasten it in placeInstallation, cont’d Video and audio output connectionsPower connection Remote connectionInstallation, cont’d Three Front Panel Controls and Indicators MVX 44 / 48 / 84 / 88 VGA Matrix Switchers OperationOperationeration, cont’d DefinitionsInput and output selection controls and indicators Power/audio/data LED and infrared sensorPower/data/audio LED Selection and audio/video controls and indicators Audio Setup buttonOperation, cont’d Control buttons and LEDsOn 4-output switchers, this button and LED stand alone Operations Powering up the switcherCreating a set of ties Select video and audio for the tie figure Example 1 Create a set of video and audio tiesPress and release the Input 5 button figure Select the outputs Press and release the Enter button figureSelect video only for the tie figure Example 2 Add a video tie to a set of video and audio tiesPress and release the Output 1 button figure Example 3 Remove a tie from a set of ties Select audio only for the tie figurePress and release the Output 4 button figure 15 Deselect the outputViewing the configuration Audio breakawayOut Example 4 View ties by selecting an input19 Select an input Press and release the I/O button figureExample 5 View ties by selecting outputs Press and release the Output 3 button figure24 Deselect audio to view video ties only Using presets Example 6 Save a presetExample 7 Recall a preset Preset 2 PresetAdjusting input audio gain and attenuation Press and release the Input 1 button figureMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Example 8 Adjust the input audio gain = unlit, = blinking LED+2 dB Lit +dB or -dB LED indicates the gain + or attenuation34 Exit Audio Setup mode Resetting audio gain single inputSetting the output audio level Resetting audio gain all inputsPress and release the and buttons simultaneously figure Front panel security lockout Executive mode Clearing all ties and presetsResetting the system to factory defaults MemoryAudio signal TroubleshootingOptimizing the Audio Worksheet example 1 System equipment WorksheetsPodium monitor Conf. room Sound VCR system USP Worksheet example 2 Daily configuration 44 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration 45 Worksheet example 3 Test configurationOperation, cont’d Configuration worksheet Output destinationsOperation, cont’d Four Host-to-Switcher instructions MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote OperationRemoteOperation,cont’d Simple Instruction Set ControlSwitcher-initiated messages Switcher error responses Using the command/response tableSymbol definitions Remote Operation, cont’dCommand/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands cont’d Global presets View ties, gain, mutes, and presets Loading firmware using an SIS command Settings Ascii SetupClick File Properties Depress the keyboard’s EscClick the Files of type drop box and select All files File figureMatrix Switchers Control Program Installing the softwareUsing the software OverviewExtron Matrix Switchers Control Program window blank Sample program window complete Updating the firmware Open windowMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Remote Operation Windows menus Windows buttons, drop boxes, and trashFile menu 11 RGB Delay/Mute/Output-Volume Adjust window Tools menu13 Ties shown as lines 14 Ties shown as crosspoints Using Emulation mode 15 Emulation mode configurationUsing the help system Remote Operation, cont’d AAppendix a SpecificationsandandPartPartNumbers,Numberscont’d SpecificationsSync Specifications and Part Numbers, cont’d Audio outputMVX Series VGA switchers Optional accessoriesPart Numbers Included partsInstall kits Part Cable assemblies PartVGA to BNC cable assemblies Part Audio cable assemblies PartFCC Class a Notice Extron’s Warranty Asia JapanExtron Electronics, USA
Related manuals
Manual 70 pages 45.03 Kb

MVX 48, MVX 84, MVX 44, MVX 88 specifications

Extron Electronics is a prominent leader in high-quality AV technology solutions, renowned for its innovative product lines designed to address diverse connectivity and distribution needs. Among their array of offerings, the MVX series stands out, particularly the MVX 44, MVX 84, and MVX 88 models, which cater to various AV signal routing needs within educational institutions, corporate environments, and large spaces.

The Extron MVX 44 is a 4x4 matrix switcher designed for routing HDMI, VGA, and audio signals. One of its key features is its ability to deliver high-resolution video up to 1080p, making it ideal for modern multimedia presentations. The MVX 44 supports EDID management, ensures compatibility with a range of source devices, and features automatic switching capabilities. It also includes a user-friendly interface for seamless operation, allowing simultaneous switching of multiple input sources to multiple outputs.

Expanding on the capabilities of the MVX 44, the MVX 84 and MVX 88 models provide enhanced functionality with additional inputs and outputs. The MVX 84 offers support for up to 8 input sources and 4 output destinations, while the MVX 88 offers 8x8 routing of signals. Both models maintain superior video quality and high-performance signal processing, accommodating more extensive AV systems. They also share features such as HDCP compliance to secure content protection, ensuring that the highest quality video signals are transmitted without degradation.

Technologically advanced, these switchers incorporate Extron's exclusive technologies, such as the Advanced Color Processing for superior color fidelity and signal reliability. Additionally, the Series comes equipped with optional control and integration capabilities, enabling connection to various AV control systems for centralized management.

The Extron MVX series matrices are built with the robustness expected from Extron products, ensuring long-term reliability in demanding environments. The integration of state-of-the-art support for audio signals allows not only video but also audio distribution, making them versatile for any AV setup. In summary, with their rich feature set, impressive scalability, and superior video processing capabilities, the Extron MVX 44, MVX 84, and MVX 88 present compelling solutions for anyone looking to streamline AV signal management in professional setups.
Top Page Image Contents