Extron electronic MSW 4SV RS, MSW 4V rs manual Installation Overview, Select an input channel

Page 9

Installation

Installation

Overview

This section provides brief instructions for installing and operating either the MSW 4V rs or the MSW 4SV rs switcher. Users are advised to follow the links to obtain more information, elsewhere in this guide, about each step.

Mount the switcher in a suitable location.

Connect the composite and S-video(MSW 4SV rs only) inputs to video sources. Connect the composite and S-video(MSW 4SV rs only) outputs to video displays. Connect the power supply (provided).

CAUTION: Read the cautions on page 6 before connecting a power supply to the switcher.

Connect the RS-232 captive screw connector to a control device such as a computer or IP Link controller (for use with an Extron TouchLink panel).

Connect the Contact captive screw connector as required. Power on the switcher and all connected devices.

Set up the auto switching mode and video mute. These can be initiated through the front panel buttons, the Universal Switcher Control Program, or by SIS commands.

Select an input channel.

MSW 4V rs and MSW 4SV rs • Installation Overview

3

Image 9

Contents Switchers MSW 4V rs and MSW 4SV rsMini Video Switchers User GuideConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolFCC Class A Notice EX! *X1& *X2 *X2# * X2!CE Conventions Used in this GuideCopyright TrademarksMSW 4V rs and MSW 4SV rs Contents ContentsMSW 4V rs and MSW 4SV rs Contents Features About the MSW 4V rs and MSW 4SV rs SwitchersAbility to detect an active signal IntroductionApplication Diagrams Figure 1. Typical Application for the MSW 4V rsFigure 2. Typical Application for the MSW 4SV rs ‰‰ Select an input channel Installation OverviewRear Panel Connections Front Panel Controls and Indicators Panel FeaturesRear Panel Connections Figure 3. MSW 4SV rs and MSW 4V rs Rear Panel Connectionsuse cable that has a drain wire, tie the drain NOTE Connect a ground wire between the switcherwire to ground at both ends Figure 4. RS-232 Connector WiringPower Supply Connection Auto Switch Mode Controls and Indicators Front Panel Controls and IndicatorsInput Selection Figure 6. MSW 4V rs and MSW 4SV rs Front PanelFigure 7. Turning on Auto Switch Mode Vertical Interval SwitchingFigure 8. Turning off Auto Switch Mode Mode SelectionInstalling the Software Universal Switcher Control ProgramFigure 10. Universal Switcher Install Link Control SoftwareUsing the Software Figure 11. Communication Setup WindowFigure 12. Universal Switcher Output Window Using the Help File Updating the FirmwareDownloading the MSW 4V rs and 4SV rs Firmware Using the Control Program to Update the Firmware Downloading and Installing the Firmware LoaderFigure 13. Firmware Loader Download Link Figure 14. Choosing Firmware LoaderFigure 16. Choose Firmware File Window Figure 15. Add Device WindowFigure 17. Firmware Upload in Progress Video- MSW 4V rs, MSW 4SV rs SpecificationsVideo input Video outputSync Control/remote - switcherGeneral NOTE Specifications are subject to change without noticeIntroduction to SIS Symbols Used in this Guide Error messages SIS CommandsCommand and Response table for SIS commands Introduction to SISSymbols Used in this Guide Error MessagesFigure 18. ASCII to HEX Conversion Table Command Command and Response Table for SIS CommandsASCII Command VX%FX$VmtX#Optional Accessories Parts and AccessoriesIncluded Parts DescriptionTabletop Placement Rack Mounting Under-desk Mounting Tabletop PlacementMounting Rack Mounting the MSW 4V rs and MSW 4SV rsUnder-desk Mounting the MSW 4V rs and MSW 4SV rs Rack Mounting the MSW 4V rs and MSW 4SV rsUSA, Canada, South America Extron WarrantyJapan and Central AmericaExtron USA - East Extron USA - WestExtron Europe Extron Asia

Related manuals

Manual 2 pages 48.13 Kb