Extron electronic MSW 4SV RS, MSW 4V rs manual Front Panel Controls and Indicators, Input Selection

Page 13
Front Panel Controls and Indicators

4.Use the supplied tie-wrap to strap the power cord to the extended tail of the connector.

5.Before connecting the power cord, verify the polarity by plugging it into the power supply with no load and checking the output with a voltmeter.

Figure 6. MSW 4V rs and MSW 4SV rs Front Panel WARNING The two power cord wires must be kept separate while the Input Selectionpower supply is plugged in. Remove power before wiring.

Alternately, an Extron PS 124 Universal 12 VDC power supply (part number

60‑1022‑01) can power up to eight MSWs or other Extron 12 VDC devices using only one AC power connector.

Front Panel Controls and Indicators

The MSW 4V rs and MSW 4SV rs have identical front panels, shown in figure 6.

61

MODE

AUTO

SWITCH

NORMAL AUTO

1

2

3

4

 

 

 

A/V SWITCHER

5

4

3

2

Figure 6. MSW 4V rs and MSW 4SV rs Front Panel

Input Selection

AInput 1 through 4 LEDs — The Input LEDs light to identify the selected input.

BInput 1 through 4 buttons — Each Input button selects the associated input for output.

The Input 1 (E), Input 2 (D), and Input 3 (C) buttons are also used to toggle auto switch mode on and off. See the following section.

Auto Switch Mode Controls and Indicators

When auto switch is activated, the switcher automatically detects and selects the highest numbered input with video sync present.

CAuto (switch) button — The Auto button is used with the Mode button (E) to select auto switch mode. Auto is a secondary function of the Input 3 button.

DNormal button — The Normal button is used with the Mode button (E) to select normal mode. Normal is a secondary function of the Input 2 button.

EMode button — The Mode button is used with the Normal button (D) or Auto button (C) to select the switching mode. Mode is a secondary function of the Input 1 button. See “Mode selection” on the next page.

FAuto Switch LED — When lit, the Auto Switch LED indicates that the switcher is in auto switch mode. In this mode, the MSW automatically switches to the highest numbered input with active sync pulses. When this LED is unlit, the switcher is in normal (manual) mode.

MSW 4V rs and MSW 4SV rs • Panel Features

7

Image 13
Contents Switchers MSW 4V rs and MSW 4SV rsMini Video Switchers User GuideConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolFCC Class A Notice EX! *X1& *X2 *X2# * X2!CE Conventions Used in this GuideCopyright TrademarksMSW 4V rs and MSW 4SV rs Contents ContentsMSW 4V rs and MSW 4SV rs Contents Features About the MSW 4V rs and MSW 4SV rs SwitchersAbility to detect an active signal IntroductionFigure 1. Typical Application for the MSW 4V rs Application DiagramsFigure 2. Typical Application for the MSW 4SV rs ‰‰ Select an input channel Installation OverviewRear Panel Connections Front Panel Controls and Indicators Panel FeaturesRear Panel Connections Figure 3. MSW 4SV rs and MSW 4V rs Rear Panel Connectionsuse cable that has a drain wire, tie the drain NOTE Connect a ground wire between the switcherwire to ground at both ends Figure 4. RS-232 Connector WiringPower Supply Connection Auto Switch Mode Controls and Indicators Front Panel Controls and IndicatorsInput Selection Figure 6. MSW 4V rs and MSW 4SV rs Front PanelFigure 7. Turning on Auto Switch Mode Vertical Interval SwitchingFigure 8. Turning off Auto Switch Mode Mode SelectionInstalling the Software Universal Switcher Control ProgramFigure 10. Universal Switcher Install Link Control SoftwareFigure 11. Communication Setup Window Using the SoftwareFigure 12. Universal Switcher Output Window Updating the Firmware Using the Help FileDownloading the MSW 4V rs and 4SV rs Firmware Using the Control Program to Update the Firmware Downloading and Installing the Firmware LoaderFigure 13. Firmware Loader Download Link Figure 14. Choosing Firmware LoaderFigure 16. Choose Firmware File Window Figure 15. Add Device WindowFigure 17. Firmware Upload in Progress Video- MSW 4V rs, MSW 4SV rs SpecificationsVideo input Video outputSync Control/remote - switcherGeneral NOTE Specifications are subject to change without noticeIntroduction to SIS Symbols Used in this Guide Error messages SIS CommandsCommand and Response table for SIS commands Introduction to SISError Messages Symbols Used in this GuideFigure 18. ASCII to HEX Conversion Table Command Command and Response Table for SIS CommandsASCII Command VX%FX$VmtX#Optional Accessories Parts and AccessoriesIncluded Parts DescriptionTabletop Placement Rack Mounting Under-desk Mounting Tabletop PlacementMounting Rack Mounting the MSW 4V rs and MSW 4SV rsUnder-desk Mounting the MSW 4V rs and MSW 4SV rs Rack Mounting the MSW 4V rs and MSW 4SV rsUSA, Canada, South America Extron WarrantyJapan and Central AmericaExtron USA - East Extron USA - WestExtron Europe Extron Asia
Related manuals
Manual 2 pages 48.13 Kb