Extron electronic MSW 4SV RS, MSW 4V rs manual FCC Class A Notice

Page 3
FCC Class A Notice

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interference that may cause undesired operation.

The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the user guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Manual background NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with Manual background the unit to ensure compliance with FCC emissions limits.

For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and

related topics, click here.

Image 3
Contents User Guide MSW 4V rs and MSW 4SV rsSwitchers Mini Video SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class A Notice Trademarks Conventions Used in this GuideEX! *X1& *X2 *X2# * X2!CE CopyrightMSW 4V rs and MSW 4SV rs Contents ContentsMSW 4V rs and MSW 4SV rs Contents Introduction About the MSW 4V rs and MSW 4SV rs SwitchersFeatures Ability to detect an active signalApplication Diagrams Figure 1. Typical Application for the MSW 4V rsFigure 2. Typical Application for the MSW 4SV rs ‰‰ Select an input channel Installation OverviewFigure 3. MSW 4SV rs and MSW 4V rs Rear Panel Connections Panel FeaturesRear Panel Connections Front Panel Controls and Indicators Rear Panel ConnectionsFigure 4. RS-232 Connector Wiring NOTE Connect a ground wire between the switcheruse cable that has a drain wire, tie the drain wire to ground at both endsPower Supply Connection Figure 6. MSW 4V rs and MSW 4SV rs Front Panel Front Panel Controls and IndicatorsAuto Switch Mode Controls and Indicators Input SelectionMode Selection Vertical Interval SwitchingFigure 7. Turning on Auto Switch Mode Figure 8. Turning off Auto Switch ModeControl Software Universal Switcher Control ProgramInstalling the Software Figure 10. Universal Switcher Install LinkUsing the Software Figure 11. Communication Setup WindowFigure 12. Universal Switcher Output Window Using the Help File Updating the FirmwareDownloading the MSW 4V rs and 4SV rs Firmware Figure 14. Choosing Firmware Loader Downloading and Installing the Firmware LoaderUsing the Control Program to Update the Firmware Figure 13. Firmware Loader Download LinkFigure 16. Choose Firmware File Window Figure 15. Add Device WindowFigure 17. Firmware Upload in Progress Video output SpecificationsVideo- MSW 4V rs, MSW 4SV rs Video inputNOTE Specifications are subject to change without notice Control/remote - switcherSync GeneralIntroduction to SIS SIS CommandsIntroduction to SIS Symbols Used in this Guide Error messages Command and Response table for SIS commandsSymbols Used in this Guide Error MessagesFigure 18. ASCII to HEX Conversion Table VX%FX$VmtX# Command and Response Table for SIS CommandsCommand ASCII CommandDescription Parts and AccessoriesOptional Accessories Included PartsRack Mounting the MSW 4V rs and MSW 4SV rs Tabletop PlacementTabletop Placement Rack Mounting Under-desk Mounting MountingUnder-desk Mounting the MSW 4V rs and MSW 4SV rs Rack Mounting the MSW 4V rs and MSW 4SV rsand Central America Extron WarrantyUSA, Canada, South America JapanExtron Asia Extron USA - WestExtron USA - East Extron Europe
Related manuals
Manual 2 pages 48.13 Kb