Extron electronic 68-1316-02 manual Wiring the Power Connector

Page 13

CRS-232 connector (SW2 and SW4 DVI Plus non-audio models only) — For RS-232 control, connect your computer serial port to this 9-pin female D connector. (For more information, see “Wiring for RS-232 Control” on page 9.)

DRemote and auto-input switching connector — This 5-pole, 3.5 mm captive screw connector (labeled “Remote/Auto-SW”) can be used for RS-232 communication with the switcher and to enable auto-input switching.

To connect for RS-232 control on all models except the non-audio SW2 and SW4 DVI Plus, connect the Tx (transmit), Rx (receive) and G (ground) pins to your computer serial port (see “Wiring for RS-232 Control”).

To enable auto-input switching, short pins 4 and 5 of this connector together. In auto-input switch mode, the switcher automatically switches to the highest numbered active input (see “Enabling Auto-input Switching” on page 10).

NOTE: The SW2 and SW4 DVI Plus non-audio models do not have this

connector. Auto-input switching on those models is enabled and disabled via an SIS command (see the “Input Selection Mode” commands in the Command and Response Table for SIS commands, “Remote Configuration and Control” section).

EAudio output connector (SW DVI A Plus models only) — Connect the audio cable from your output device to this 5-pole, 3.5 mm captive screw connector for balanced (+6 dB) or unbalanced (0 dB) audio (see “Wiring the Audio Connectors (SW DVI A Plus Models)” on page 8).

NOTE: If the output device is wired for unbalanced audio, the gain is unity. If the

output is wired for balanced audio, a +6 dB gain is applied.

FAudio input connectors (SW DVI A Plus models only) — Connect the audio cables from your input sources to these 3.5 mm TRS mini jacks for unbalanced stereo audio.

GPower connector — Plug the provided external 12 VDC power supply into this 2-pole,

3.5 mm captive screw connector.

Wiring the Power Connector

If using a different external power supply from the one provided with the SW DVI Plus, you may need to wire the power supply connector as follows:

1.Cut the DC output cord to the length needed.

2.Strip the jacket to expose 3/16 inch (5 mm) of the conductors.

CAUTIONS: Exposing more than 3/16 inch (5 mm) of the copper wires could allow the stripped wires to touch each other, causing a short circuit. This could result in the external DC power supply overheating and burning.

Stripping the wires to expose less than the recommended amount may cause them to slide out of the connector too easily, even if they are tightly pinched by the captive screws.

SW DVI Plus Series • Installation

7

Image 13
Contents SW DVI Plus Series DVI SwitchersSafety Instructions English FCC Class a Notice Conventions Used in this Guide Software CommandsNotifications Contents SW DVI Plus Series Contents About this Guide IntroductionAbout the SW DVI Plus Series Features Connection Diagram for an SW4 DVI Plus Switcher Application DiagramsInstallation Overview InstallationSW2 DVI Plus Rear Panel Rear Panel FeaturesSW6 DVI a Plus Rear Panel Wiring the Power Connector Audio Input Wiring the Audio Connectors SW DVI a Plus ModelsSW2 and SW4 DVI Plus RS-232 Connector Wiring for RS-232 ControlAll Other Models Remote/Auto-SW Connector Audio OutputSW2/SW4 DVI Plus Non-audio Models Enabling Auto-input SwitchingAll Other Models Remote/Auto-SW Connector with Jumper Operation Front Panel FeaturesOperations Powering On the SwitcherSelecting an Input Remote control buttons Using the Optional IR 102 Remote ControlLocking IR remote access Setting Equalization for Input Sources Enabling Front Panel Lockout Executive ModeAutomatic mode Edid ModesChanging the Edid mode User-assigned Edid modeNative Resolution Refresh Rate 1024 x 768 defaultResetting Using Simple Instruction Set SIS Commands Remote Configuration ControlHost-to-switcher Communications Switcher-initiated MessagesUsing the Command and Response Table Error ResponsesSymbol Definitions Input Selection Mode Command and Response Table for SIS CommandsInput Video Signal Sensing Video Output MutingDisable IR Receiver from Front Panel Front Panel Lockout Executive ModeUpload Firmware ResetDownloading and Installing the Software from the Web Universal Switcher Control ProgramInstalling the Software from the DVD Software Button on the DVD Window Starting the ProgramUsing the Help System Updating Firmware Using Firmware LoaderDownloading and Installing Firmware Loader Firmware Loader Download Link Downloading the SW DVI Plus FirmwareConnection Method Menu on the Add Device Window Loading the Firmware to the SwitcherOpen Window for Firmware File Selection Firmware Loader Screen with an SW DVI Plus Added Firmware Upload in Progress Reference Information SpecificationsAudio output Control/remote switcherGeneral EMI/EMC Part Numbers AccessoriesIncluded Parts Cables and AdaptersTabletop use Mounting the SW DVI Plus SwitcherRack mounting UL rack mounting guidelinesBack of the rack mounting Mounting an SW DVI Plus to a Back of the Rack Support Rack mounting the SW6 DVI Plus and SW8 DVI PlusFurniture Mounting SW2 and SW4 DVI Plus Only Extron Warranty

68-1316-02 specifications

The Extron Electronic 68-1316-02 is a versatile, professional-grade component designed for seamless integration into various audio-visual systems. Designed primarily for the educational and corporate environments, this device offers a range of features that enhance user experience and operational reliability.

One of the main features of the Extron 68-1316-02 is its robust connectivity options. Equipped with multiple input and output configurations, it supports a wide range of devices including computers, projectors, and displays. This flexibility ensures that various audio and video sources can be connected effortlessly, allowing for an efficient and dynamic setup.

The device utilizes Extron's renowned signal processing technology, which provides superior signal integrity and quality. This technology minimizes signal degradation, ensuring that high-definition images and clear audio are delivered consistently. Additionally, the unit supports resolutions up to 4K, making it suitable for modern high-resolution display systems.

Another characteristic that sets the Extron 68-1316-02 apart is its intuitive user interface. The device features a straightforward control panel that allows users to navigate through settings and options easily. This user-centric design ensures that even individuals with minimal technical expertise can operate the system effectively.

Moreover, the Extron 68-1316-02 includes advanced features such as EDID (Extended Display Identification Data) management, which optimizes the compatibility between the connected sources and displays. This reduces the occurrence of display issues, contributing to a smoother operation in environments where multiple devices are utilized.

The device also boasts a range of mounting options, whether ensuring it fits seamlessly within a rack or being wall-mounted in a conference room. Its compact design allows for flexible placement in various settings without compromising on performance.

Further enhancing its appeal, the Extron 68-1316-02 comes with comprehensive technical support and documentation, which ensures that users can maximize the device's potential.

In conclusion, the Extron Electronic 68-1316-02 is a highly capable component tailored for the demands of contemporary audiovisual environments. With its excellent connectivity, superior signal processing technology, and user-friendly features, it stands out as a reliable solution for educational and corporate applications alike, facilitating enhanced communication and collaboration.