Extron electronic TPS150 manual Optimizing the Video

Page 26

Operation, cont’d

Optimizing the Video

The TPR150 receiver features cable equalization controls for high and low frequency adjustments and RGB skew control to compensate for misconvergence of colors that can result from long CAT 5 cable runs. The following steps detail how to use these features to optimize the output image.

These adjustments should be made with the highest resolution input selected on the TPT150 transmitter.

1.

Carefully set the rear panel RGB skew controls to minimum

 

(fully counterclockwise).

 

 

 

2.

Power up the transmitter, receiver, and display.

 

3.

Select the highest resolution.

 

 

 

4.

As needed, use the front panel low

 

CABLE EQUALIZATION

 

 

frequency control to eliminate any

- ADJUST +

SELECT

 

visible image smear.

 

 

 

a. If necessary, press and release the Cable Equalization Select

button to light the Low Frequency LED.

SKEW ADJ

RED BLUE GRN

LOW FREQ.

HIGH FREQ.

 

b.

Press the + side of the button to increase the amount of equalization

 

 

applied to the output signal’s low frequency range. Press the – side of

 

 

the button to decrease the amount of equalization.

5.

As needed, use the front panel high frequency control to maximize the detail

 

and sharpness.

 

a.

If necessary, press and release the Cable Equalization Select button to

 

 

light the High Frequency LED.

 

b.

Press the + side of the button to increase the amount of equalization

 

 

applied to the output signal’s high frequency range. Press the – side of

 

 

the button to decrease the amount of equalization.

6.

If the red, green, and blue video are not properly aligned, use a Tweeker or

 

small screwdriver to gently adjust the red, green, and/or blue Skew

 

Adjustment controls to correct for the delay inherent in network (CAT 5)

 

cable.

 

 

The Skew Adjustment controls are sensitive. Make each adjustment carefully.

 

 

7.

Repeat steps 4 through 6 to fine tune the adjustments.

3-6 TPS150 Switching and Transmission System • Operation

Page 25 Page 27
Image 26
Page 25 Page 27
Contents TPS150 Precautions Inputs 3 TPS150 Switching and Transmission System Quick Start QS-1Inputs 1 and 2 Connect two RGB video sources QS-2 TPS150 Switching and Transmission System Quick Start Quick Start TPS150 Switching and Transmission SystemVolume and buttons Output 1 Connect aTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d About the TPT150 switching transmitterTPS150 Switching and Transmission System Introduction About this ManualAbout the TPR150 receiver Component video Y, R-Y, B-Y on three female RCA connectorsSerial RS-232 commands on one male DB9 connector TP Cable Advantages FeaturesIntroduction, cont’d Transmission distanceTPS150 Switching and Transmission System Introduction Introduction, cont’d Two Rack mounting the transmitter Installationstallation, cont’dMounting the Transmitter and Receiver Projector mounting the receiver Projector mounting the receiverTransmitter connections Installation, cont’dCabling and Rear Panel Views Video and audio input connectionsRemote control connections TP and audio output connectionsUTP Link Input connection Power connectionReceiver connections Video output connections Serial connectionTP Cable Termination RJ-45Three TPS150 Switching and Transmission System Operation Controls and IndicatorsTransmitter controls and indicators Operationeration, cont’dReceiver controls and indicators TPR150 receiver front panelOperation, cont’d PowerProjector power OperationsReceiver reset Volume adjustmentFull system reset Output volumeOptimizing the Video Troubleshooting General checksDistorted image Specific problemsProblem Possible cause Solution No image appears AppearsFour ICS100 Windows-Based Control Program Installing the softwareSerialCommunicationsunications, cont’d System requirementsEstablishing communications with the program ICS100 program window and connected messageSerial Communications, cont’d AgainConnected window Using the software to configure the serial port settings Using the software to program the input and projector codes For each input or projector code to be programmedCode entry Ascii code Using the software to operate the transmission system Window appears figureUsing the help system Button mutes and unmutes the audio outputCommunication protocols Serial CommandsCommand and response structure Addressing the transmitterR0addressecho of the command sent Using the command/response tableSymbols R1addressecho of the command sentSpaces between bytes are not allowed Command Ascii Command Response Additional description AddressingInput audio level Command Response Additional descriptionFront panel lockout Serial Communications, cont’d AAppendix a Specifications Reference InformationSync Reference Information, cont’d Control projector TPR onlyPart Numbers Optional accessoriesAccessory Part number Included partsReference Information, cont’d FCC Class a Notice Extron’s Warranty Asia JapanExtron Electronics, USA
Related manuals
Manual 52 pages 17.77 Kb

TPS150 specifications

The Extron TPS150 is a highly regarded touch panel system designed for professional AV environments, providing an intuitive interface for controlling various audio and video components. This device is part of Extron's popular TouchLink Pro series, which is known for its robustness and versatility in managing classroom and conference room technology.

One of the standout features of the TPS150 is its high-resolution capacitive touch screen, which measures at 15 inches. This screen delivers vibrant colors and exceptional clarity, ensuring that users can easily interact with the device even in well-lit environments. The touch panel's interface is fully customizable, allowing users to create a layout tailored to their specific needs. This customization can include the addition of buttons, sliders, and dynamic graphics that make navigation seamless and user-friendly.

In terms of connectivity, the TPS150 supports Ethernet communication, which enables easy integration with networked AV systems. This feature allows for remote access and control, making it easier for IT professionals to monitor and manage AV devices from a centralized location. Additionally, the TPS150 is compatible with various Extron control systems, providing a robust platform for managing complex multimedia setups.

The device also incorporates advanced security features, ensuring that sensitive system controls are protected from unauthorized access. Administrators can establish user permissions and authentication processes to maintain control over the AV environment, which is particularly important in corporate and educational settings.

Moreover, the TPS150 supports Extron's global configurator software, which simplifies the setup process and allows for easy programming of touch panel interfaces. Users can design custom layouts quickly and efficiently, and the software also provides an extensive library of drivers for popular AV equipment, enhancing compatibility and functionality.

With its elegant design, high-quality components, and customizable interface, the Extron TPS150 touch panel offers an effective solution for AV control. Whether used in educational, corporate, or professional environments, it empowers users to streamline their audiovisual experiences and maintain effective control over their technology, ensuring successful presentations and meetings.
Top Page Image Contents