Extron electronic CTL208CM user manual Installationtal ation, cont’d Installation Overview

Page 8

Installationtal ation, cont’d

Installation Overview

CAUTION Installation and service must be performed by authorized personnel only. UL Listed electrical boxes are recommended. See UL Requirements for Wall Box Installation in this chapter.

1If desired, order a custom engraved front panel. Contact the Extron S3 Sales & Technical Support Hotline to order the panel.

2Power off all devices and disconnect them from the power source, if necessary.

3Run a serial cable between the site where the CTL208CM control panel module will be installed and the site of the serial-controlled device.

4For installation in a wall or furniture, prepare the site: cut a hole in the surface, install the electrical box or mounting bracket, and prepare the cables. See Wall Mounting Site Preparation in this chapter. See appendix A, Reference Information, for a partial list of devices that can accept four space mini-AAPs.

5For other installations, install a tabletop or in-table connector bay, or other mini-AAP mounting option. Refer to the manual for the device in which the control panel module will be installed. See appendix A, Reference Information, for a partial list of devices that can accept four space mini-AAPs.

6Connect a serial cable between the control panel module and a computer. See Rear Panel Setup, in this chapter for details.

Alternatively, you can connect the control panel module to an RS-485 serial port daisy chain that includes the programming computer and the device to be controlled. In a daisy-chain configuration, you can make changes to the control panel module’s button programming as needed, without removing the panel from its installation.

7If necessary, configure the control panel module’s rear panel DIP switches to match the serial protocol (RS-232, RS-422, RS-485) of the computer used to program the control panel module. See Rear Panel Setup, in this chapter for details.

8Connect the power source to the control panel module. See Rear Panel Setup, to wire the power connector.

9Program the control panel module’s buttons as desired, using either the Extron ICS100 control software or the Extron serial character command set. See ICS100 Windows Control Program and/or Serial Commands in chapter 4, Serial Communications, for details.

10If necessary, configure the control panel module’s serial control protocol settings (baud rate, data bits, and stop bits) to match those of the device to be controlled. See ICS100 Windows Control Program and/or Serial Commands in chapter 4, Serial Communications, for details.

11If necessary, reconfigure the control panel module’s rear panel DIP switch 1 to match the serial protocol (RS-232, RS-422, RS-485) of the device to be controlled. See Rear Panel Setup, in this chapter for details.

12If the computer, control panel module, and the device to be controlled are not part of an RS-485 serial port daisy chain, disconnect the serial control cable from the computer and install the serial control cable between the control panel module and the device to be controlled.

If the rear of the control panel module will be inaccessible when the installation is complete, the operation of the module should be tested before the final mounting.

13Apply or connect power to all devices in the system.

14Test the system: Ensure that the controlled device responds as desired to the control panel module buttons. If necessary, correct the programming and/or the system wiring. Ensure that you remove electrical power if you need to change the system wiring. Test the system again.

15Disconnect power from the control panel module and other devices.

16Mount the control panel module into any Extron four- space mini-AAP connector panel.

If the rear of the control panel module will be inaccessible when the installation is complete, all cables, including the power connector on the CTL208, must be connected before the permanent installation.

17Mount the mini-AAP connector panel to the mini-AAP mounting option as necessary. See Wall mounting in this chapter for details about wall mounting the panel.

18Restore power to all devices.

2-2

CTL208CM Control Panel Module • Installation

CTL208CM Control Panel Module • Installation

2-3

Image 8 Extron electronic Installationtal ation, cont’d Installation Overview, CTL208CM Control Panel Module Installation
Contents CTL208CM Extron’s Warranty FCC Class a NoticeQuick Start Guide CTL208CM CTL208CM Control Panel Module Quick Start Guide QS-1Table of Contents Table of Contents, cont’d IntroductionCTL208CM Control Panel Module Introduction FeaturesIntroductionroduction, cont’d About the CTL208CM Installation Introduction, cont’dInstallationtal ation, cont’d Installation Overview CTL208CM Control Panel Module InstallationWall Mounting Site Preparation CTL208CMInstallation, cont’d Device ConfigurationInstallation, cont’d Wall Mounting Rear Panel Setup10 CTL208CM Control Panel Module Installation Captive screw power connector Power the control panel12 CTL208CM Control Panel Module Installation OperationCTL208CM Control Panel Module Operation Send Programmed CommandsOperationration, cont’d Button Modes Operation, cont’d Factory ResetSerial Communications Installing the software SerialCommunicationsunications,cont’dICS100 Windows Control Program System requirementsUsing the software to program the CTL208CM Serial Communications, cont’dToggle Mode Timeout window Serial Commands Using the help systemCommand and response structure Communication protocols10 CTL208CM Control Panel Module Serial Communications Using the command/response tableControl panel module responses Command/response table for programming the CTL208 CommandAdditional description Response 12 CTL208CM Control Panel Module Serial CommunicationsCommand Ascii Command Response Additional description Button mode programmingButton timeout programming 14 CTL208CM Control Panel Module Serial CommunicationsReference Information AAppendixReferenceInformation,cont’d Specifications Parts ListReference Information, cont’d Wall mounting harware
Related manuals
Manual 1 pages 28.04 Kb

CTL208CM specifications

The Extron CTL 208 CM is a sophisticated control system designed for seamless integration and management of AV systems in various environments, such as educational institutions, corporate spaces, and any setting requiring robust audiovisual control. Known for its user-friendly interface and advanced features, the CTL 208 CM stands out in its category.

One of the primary features of the CTL 208 CM is its ability to control multiple AV devices through a single platform. This centralized control facilitates ease of operation for users, allowing them to manage projectors, displays, sound systems, and other devices without the need to juggle multiple remotes or interfaces. This is particularly beneficial in environments where educators or presenters need to focus on delivering their content without getting bogged down by technicalities.

The CTL 208 CM is equipped with Extron’s proprietary technologies, which enhance its performance and reliability. Notable among these is the Extron Control App, which allows users to create custom controls via a tablet or smartphone. This not only streamlines the user experience but also enables personalized settings, ensuring users can quickly access the devices they need.

Additionally, the CTL 208 CM features customizable button layouts and a graphic interface that simplifies operation, regardless of the user's technical proficiency. This flexibility is crucial in environments where users may vary significantly in their comfort level with technology.

The system's advanced communication capabilities enable it to integrate seamlessly with a variety of third-party devices, expanding its functionality and compatibility. This open architecture design supports popular protocols such as RS-232, IP control, and infrared, allowing users to implement it alongside existing infrastructures effectively.

Moreover, the CTL 208 CM boasts a scalable architecture, making it suitable for small to large installations. Users can easily expand their control system as their needs evolve without requiring a complete overhaul of their existing setup.

In summary, the Extron CTL 208 CM is a powerful control solution that combines ease of use with extensive functionality. Its advanced technologies and features position it as an ideal choice for anyone seeking a reliable and versatile AV control system. With its ability to simplify AV management and enhance user engagement, the CTL 208 CM is a valuable asset for modern audiovisual environments.