Rack mounting
Rack mount the switcher as follows:
1. Attach the rack mounting brackets to the switcher with the eight provided #8 machine screws (figure 2-1).
2. Insert the switcher into the rack, align the holes in the mounting bracket with those of the rack.
3. Secure the switcher to the rack using the supplied machine screws.
Cabling and Rear Panel Views
All connectors are on the rear panel. Figure 2-2 shows the rear panel of the CrossPoint 42 HVA.
1.5A MAX | | | | | | | | | | | | | | | | 1 | 2 | 3 | 4 | 1 | 2 | |
| | | | | | | | | | | | | | | | | |
| 1 | | | | | 3 | | | | | | | 1 | | | | L | | | L | | L | |
1 | R | G | B | H | V | R | G | B | H | V | 1 2 | 3 4 | R | G | B | H | V | | | | | | 6 |
| | | | | | | | | | H VH V H VH V | | | | | R | | | R | | R |
| 2 | | | | | 4 | | | | | ON | | 2 | | | | | | | | | | |
| | | | | | | | | | | | | | | | AUDIO | | AUDIO | |
| | | | | | | | | | | | | | | | | | | | |
100-240V | 50-60Hz | | | | | INPUTS | | | | | | | | | OUTPUTS | | | | INPUTS | | OUTPUTS | RS232 |
| | | | | | | | | | | | | | | | | | |
4 5
Figure 2-2 — Rear panel connectors, CrossPoint 42 HVA
Power connection
1AC power connector — Plug a standard IEC power cord into this connector to connect the switcher to a 100 to 240VAC, 50 Hz or 60 Hz power source.
Video input and output connections
All video input and output connections to the CrossPoint 42 are made with female BNC connectors. Some types of video output devices do not have BNC video output connectors. For these cases, a suitable cable or connector adapter is necessary between the device output connector and the BNC input connector of the CrossPoint.
RGBHV video inputs — Connect RGBHV video inputs to these BNC connectors for each input.
RGBHV video outputs — Connect RGBHV video outputs to these BNC connectors for each output.
The CrossPoint 42 HVA switcher can also switch RGBS, RGsB, RsGsBs, component video, S-video, or composite video by using four, three, two, or one BNC. If switching a video format other than RGBHV, ensure that the same video planes (R, G, B, H/HV, and/or V) are used on the switcher output as on the input. H/HV and V will switch sync signals only, but will not switch video.
The CrossPoint 42 HVA switcher does not alter the video signal in any way. The signal output by the switcher is in the same format as the input.
CrossPoint 42 HVA Matrix Switcher • Installation | 2-3 |
CrossPoint 42 HVA
CrossPoint Matrix Switcher
Consignes de Sécurité Français
Safety Instructions English
Sicherheitsanleitungen Deutsch
Instrucciones de seguridad Español
Quick Start CrossPoint 42 HVA
Quick Start CrossPoint 42 HVA, cont’d
View and adjust audio level
View ties
Front Panel Controls
Table of Contents
Table of Contents, cont’d
Introduction
One
About the CrossPoint 42 Matrix Switcher
CrossPoint 42 HVA Matrix Switcher Introduction
VCR
Features
Any input to any output
Introduction, cont’d
Two
Installation
Mounting the Switcher
Installationstallation, cont’d
CrossPoint 42 HVA Matrix Switcher Installation
Table or wall mounting
Cabling and Rear Panel Views
Power connection
Rack mounting
Video input and output connections
Audio input and output connections
Installation, cont’d
MKP 1000 User’s Manual for details
RS-232 connection
Installation, cont’d
Operation
Three
Operationeration, cont’d
Front Panel Controls and Indicators
Definitions
Input buttons, output buttons, and LEDs
Creating a configuration
Power
Front Panel Operations
Example 2 Changing the audio input to an existing tie
Operation, cont’d
Viewing and adjusting the audio level
Viewing the current configuration
Example 3 Viewing and adjusting an audio level
Executive mode front panel security lockout
System reset to factory defaults
Rear Panel Controls
Sync termination switches
Operation, cont’d
Programmer’s Guide
Four
Switcher-Initiated Messages
Host-to-Switcher Instructions
CrossPoint 42 HVA Matrix Switcher Programmer’s Guide
Programmer’ser’sGuide,Guidecont’d
Switcher Error Responses
Using the Command/Response Table
Command/Response Table
Symbol Definitions
Programmer’s Guide, cont’d
Command Ascii Command Response Additional description
Response Additional description
Command
Programmer’s Guide, cont’d
Five
Switcher Software
Using the software
Installing the software
Using the help system
MatrixSoftware,cont’d
Universal Switcher Control Program Main Menu window
Matrix Software, cont’d
AAppendix a
Specifications and Part Numbers
Video
SpecificationsandandPartPartNumbes,Numberscont’d
Audio input
Optional accessories
Specifications and Part Numbes, cont’d
Part Numbers
CrossPoint part numbers
Pre-cut cables
Assorted connectors BNC connectors
Extron Part BNC-4 Mini HR Cable
Specifications and Part Numbes, cont’d
Reference Information
AppendixBB
Opening the switcher
Hardware Upgrade and Maintenance
Closing the switcher
Installing a firmware update
Figure B-3 Front panel board
Reference Information, cont’d
Ensure that the switcher is working properly
Replacing the AC fuse
Reconnect the input and output cables
Asia Japan
FCC Class a Notice Extron’s Warranty
Extron Electronics, USA