Operation, cont’d
4.If audio and video are tied to different inputs (audio breakaway), and if you select video and audio for display, the LED for the selected video input lights steadily and the LED for the selected audio input blinks.
5.If an output with no tie is selected, only that output’s LED lights.
Example 1: Create a set of video and audio ties — input 3 to output 1
See figure 3-2 and the following steps for an example in which input 3 is tied to output 1.
This example assumes that there are no ties in the current configuration.
LED key: = off, | = on, B = blinking, |
1 | VIDEO/+dB |
|
2 | AUDIO/-dB |
| CONF/SAVE |
BA
Figure 3-2 — Example 1: Creating a tie
APress and release the Conf/Save button to select both video and audio for a tie.
BPress and release the Outputs button to cycle through the outputs, selecting output 1.
CPress and release the Input 3 button. The LED for input 3 lights to indicate selection.
Example 2: Changing the audio input to an existing tie
See figure 3-3 and the following steps for an example in which a new audio tie is added to the current configuration.
LED key: = off, | = on, B = blinking, |
1 | VIDEO/+dB |
|
2 | AUDIO/-dB |
| CONF/SAVE |
BA
Figure 3-3 — Example 1: Changing the audio input
APress and release the Conf/Save button to select Audio for a tie.
BPress and release the Outputs button to cycle through the outputs, selecting output 1.
CPress and release the input 2 button. The LED for input 2 lights to indicate selection.
Press the Conf/Save button to select both video and audio. The LED for input 3 should light steadily for video and the LED for input 2 should blink for audio.
3-4 CrossPoint 42 HVA Matrix Switcher • Operation
CrossPoint Matrix Switcher
CrossPoint 42 HVA
Safety Instructions English
Consignes de Sécurité Français
Sicherheitsanleitungen Deutsch
Instrucciones de seguridad Español
Quick Start CrossPoint 42 HVA
View and adjust audio level
Quick Start CrossPoint 42 HVA, cont’d
View ties
Front Panel Controls
Table of Contents
Table of Contents, cont’d
One
Introduction
CrossPoint 42 HVA Matrix Switcher Introduction
About the CrossPoint 42 Matrix Switcher
Features
VCR
Introduction, cont’d
Any input to any output
Installation
Two
Installationstallation, cont’d
Mounting the Switcher
CrossPoint 42 HVA Matrix Switcher Installation
Table or wall mounting
Power connection
Cabling and Rear Panel Views
Rack mounting
Video input and output connections
Installation, cont’d
Audio input and output connections
RS-232 connection
MKP 1000 User’s Manual for details
Installation, cont’d
Three
Operation
Front Panel Controls and Indicators
Operationeration, cont’d
Definitions
Input buttons, output buttons, and LEDs
Front Panel Operations
Power
Creating a configuration
Operation, cont’d
Example 2 Changing the audio input to an existing tie
Example 3 Viewing and adjusting an audio level
Viewing the current configuration
Viewing and adjusting the audio level
System reset to factory defaults
Executive mode front panel security lockout
Sync termination switches
Rear Panel Controls
Operation, cont’d
Four
Programmer’s Guide
Host-to-Switcher Instructions
Switcher-Initiated Messages
CrossPoint 42 HVA Matrix Switcher Programmer’s Guide
Programmer’ser’sGuide,Guidecont’d
Using the Command/Response Table
Switcher Error Responses
Command/Response Table
Symbol Definitions
Command Ascii Command Response Additional description
Programmer’s Guide, cont’d
Command
Response Additional description
Programmer’s Guide, cont’d
Switcher Software
Five
Installing the software
Using the software
Using the help system
MatrixSoftware,cont’d
Universal Switcher Control Program Main Menu window
Matrix Software, cont’d
Specifications and Part Numbers
AAppendix a
SpecificationsandandPartPartNumbes,Numberscont’d
Video
Audio input
Specifications and Part Numbes, cont’d
Optional accessories
Part Numbers
CrossPoint part numbers
Extron Part BNC-4 Mini HR Cable
Assorted connectors BNC connectors
Pre-cut cables
Specifications and Part Numbes, cont’d
AppendixBB
Reference Information
Hardware Upgrade and Maintenance
Opening the switcher
Closing the switcher
Installing a firmware update
Figure B-3 Front panel board
Ensure that the switcher is working properly
Reference Information, cont’d
Replacing the AC fuse
Reconnect the input and output cables
FCC Class a Notice Extron’s Warranty
Asia Japan
Extron Electronics, USA