Reference Information, cont’d
8. | Ensure that the switcher is working properly. |
9.If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.
10. Reconnect the input and output cables.
Replacing the AC fuse
The AC fuse on the power supply board is a user-replaceable component of the CrossPoint 42. To replace the AC fuse, do the following:
Fuse
R
G
B
H
3
V
R 4
INPUTS
G
B
H
V
| 1 | | |
HV 2 | 3 | 1 |
ON | HV | |
| | HV 4 | |
| | HV | |
| | | R |
| | | 2 |
| | | G |
| | | B |
| | | OUTPUTS |
H V
Figure B-5 — Replacing the AC Fuse
1.Follow the instructions in Opening the switcher on page B-2 to remove the top cover.
2.Locate the fuse on the power supply board (see figure B-5), and remove it from its retaining clips.
3.If test equipment is available, you can check the fuse.
4.Place a new 2A/250V fast-blow fuse in the retaining clips.
5.Reinstall the switcher’s cover. See Closing the switcher on page B-2.
If you choose to check the switcher for proper operation before putting the cover back on, ensure that tools and hands are outside the switcher, then connect the power cord to the unit and to an AC source. The switcher should power up normally. Unplug the AC power cord and reinstall the cover.
6.Attach the power cord to the switcher and to the AC power source. Make sure the switcher is working properly.
7.If the switcher was removed from a rack, remove its power cord, reattach the switcher to the rack, and reconnect the power cord.
8. | Reconnect the input and output cables. |
B-4 CrossPoint 42 HVA Matrix Switcher • Reference Information
CrossPoint Matrix Switcher
CrossPoint 42 HVA
Safety Instructions English
Consignes de Sécurité Français
Sicherheitsanleitungen Deutsch
Instrucciones de seguridad Español
Quick Start CrossPoint 42 HVA
View and adjust audio level
Quick Start CrossPoint 42 HVA, cont’d
View ties
Front Panel Controls
Table of Contents
Table of Contents, cont’d
One
Introduction
CrossPoint 42 HVA Matrix Switcher Introduction
About the CrossPoint 42 Matrix Switcher
Features
VCR
Introduction, cont’d
Any input to any output
Installation
Two
Installationstallation, cont’d
Mounting the Switcher
CrossPoint 42 HVA Matrix Switcher Installation
Table or wall mounting
Power connection
Cabling and Rear Panel Views
Rack mounting
Video input and output connections
Installation, cont’d
Audio input and output connections
RS-232 connection
MKP 1000 User’s Manual for details
Installation, cont’d
Three
Operation
Front Panel Controls and Indicators
Operationeration, cont’d
Definitions
Input buttons, output buttons, and LEDs
Front Panel Operations
Power
Creating a configuration
Operation, cont’d
Example 2 Changing the audio input to an existing tie
Example 3 Viewing and adjusting an audio level
Viewing the current configuration
Viewing and adjusting the audio level
System reset to factory defaults
Executive mode front panel security lockout
Sync termination switches
Rear Panel Controls
Operation, cont’d
Four
Programmer’s Guide
Host-to-Switcher Instructions
Switcher-Initiated Messages
CrossPoint 42 HVA Matrix Switcher Programmer’s Guide
Programmer’ser’sGuide,Guidecont’d
Using the Command/Response Table
Switcher Error Responses
Command/Response Table
Symbol Definitions
Command Ascii Command Response Additional description
Programmer’s Guide, cont’d
Command
Response Additional description
Programmer’s Guide, cont’d
Switcher Software
Five
Installing the software
Using the software
Using the help system
MatrixSoftware,cont’d
Universal Switcher Control Program Main Menu window
Matrix Software, cont’d
Specifications and Part Numbers
AAppendix a
SpecificationsandandPartPartNumbes,Numberscont’d
Video
Audio input
Specifications and Part Numbes, cont’d
Optional accessories
Part Numbers
CrossPoint part numbers
Extron Part BNC-4 Mini HR Cable
Assorted connectors BNC connectors
Pre-cut cables
Specifications and Part Numbes, cont’d
AppendixBB
Reference Information
Hardware Upgrade and Maintenance
Opening the switcher
Closing the switcher
Installing a firmware update
Figure B-3 Front panel board
Ensure that the switcher is working properly
Reference Information, cont’d
Replacing the AC fuse
Reconnect the input and output cables
FCC Class a Notice Extron’s Warranty
Asia Japan
Extron Electronics, USA