Gigabyte GA-M52S-S3P FUSB1/FUSB2/FUSB3 USB Headers, Yellow, CI Chassis Intrusion Header

Page 28

English

15)F_USB1/F_USB2/F_USB3 (USB Headers, Yellow)

The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

 

 

Pin No.

Definition

 

 

1

Power (5V)

 

 

2

Power (5V)

2

10

3

USB DX-

 

 

4

USB DY-

1

9

5

USB DX+

 

 

6

USB DY+

 

 

7

GND

 

 

8

GND

 

 

9

No Pin

 

 

10

NC

Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.

16)CI (Chassis Intrusion Header)

This motherboard provides a chassis detection feature that detects if the chassis cover has been removed. This function requires a chassis with chassis intrusion detection design.

 

Pin No.

Definition

1

1

Signal

 

2

GND

GA-M52S-S3P Motherboard

- 28 -

Image 28
Contents GA-M52S-S3P Motherboard Copyright DisclaimerDocumentation Classifications Identifying Your Motherboard RevisionTable of Contents Drivers Installation Box Contents GA-M52S-S3P Motherboard Layout Block Diagram Hardware Installation Installation PrecautionsProduct Specifications USB4 Mbit flash Installing the CPU and CPU Cooler Installing the CPUCPU Socket Locking Lever Installing the CPU Cooler Installing the Memory Dual Channel Memory ConfigurationInstalling a Memory Installing an Expansion Card Back Panel Connectors Center/Subwoofer Speaker Out Jack Orange Rear Speaker Out Jack BlackSide Speaker Out Jack Gray Line In Jack BlueInternal Connectors Pwrled Clrcmos BatteryGND FDD Floppy Disk Drive Connector CPUFAN/SYSFAN Fan HeadersIDE IDE Connector SATAII0/1/2/3 Sata 3Gb/s ConnectorsPwrled System Power LED Header BatteryFpanel Front Panel Header Cdin CD In Connector Faudio Front Panel Audio HeaderSpdifi S/PDIF In Header Spdifo S/PDIF Out HeaderFUSB1/FUSB2/FUSB3 USB Headers, Yellow CI Chassis Intrusion HeaderClrcmos Clearing Cmos Jumper English Chapter Bios Setup Startup Screen Logo Screen DefaultPost Screen Bios Setup Program Function Keys Sample Bios Version FAcMain Menu „ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationsDate TimeIDE Channel 0 Master/Slave IDE Channel 2/3 Master/SlaveFloppy 3 Mode Support Drive aHalt on MemoryHard Disk Boot Priority First/Second/Third Boot DevicePassword Check HDD S.M.A.R.T. CapabilityFull Screen Logo Show Away ModeInit Display First Integrated Peripherals IDE DMA transfer access IDE Prefetch ModeOnchip Sata Mode nVIDIA nForce 520 chipset NV Sata Pri-Master RAIDSmart LAN LAN Cable Diagnostic Function When No LAN Cable Is AttachedOnboard LAN Boot ROM Parallel Port ModeECP Mode Use DMA Onboard Serial PortPME Event Wake Up Modem Ring OnPower-On by Alarm Hpet Mode NotePower On By Mouse Power On By KeyboardPnP/PCI Configurations Reset Case Open Status Current System/CPU TemperatureSystem/CPU Warning Temperature Case OpenedCPU Smart FAN Mode System Smart FAN ControlCPU Frequency Pcie ClockCPU Clock Ratio Robust Graphics BoosterCPU Voltage Control DDR2 Voltage ControlNormal CPU Vcore Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Installing Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Before You Begin Xpress Recovery2System Requirements Installation and Configuration Installing Windows XP and Partitioning the Hard DriveEnglish Accessing Xpress Recovery2 Using the Backup Function in Xpress Recovery2Removing the Backup Using the Restore Function in Xpress Recovery2Exiting Xpress Recovery2 Bios Update Utilities Updating the Bios with the Q-Flash UtilityUpdating the Bios English Installing and Using @BIOS Updating the Bios with the @BIOS UtilityOptions and Instructions Update the Bios without Using the Internet Update Function EasyTune EasyTune 5 Interface Button Information TableWindows Vista ReadyBoost Configuring Sata Hard Drives Configuring the Onboard Sata ControllerTo configure Sata hard drives, follow the steps below Installing Sata hard drives in your computerConfiguring Sata controller mode in Bios Setup Configuring RAID set in RAID Bios YES BBS Required for Ahci and RAID Mode Making a Sata RAID/AHCI Driver DisketteInstalling the Sata RAID/AHCI Driver and Operating System Installing Windows XPSelect Nvidia nForce Storage Controller and press Enter Enter= Continue R=Repair F3=Exit Installing Windows Vista English Configuring 2/4/5.1/7.1-Channel Audio Configuring Audio Input and OutputConfiguring Speakers Configuring Sound Effect Configuring AC97 AudioInstalling the S/PDIF In Cable Installing the S/PDIF In Cable OptionalPdif Pdif Out Configuring S/PDIF outConneting a S/PDIF out Cable Configuring Microphone Recording English Recording the Sound Using the Sound RecorderPlaying the Sound Troubleshooting Frequently Asked QuestionsTroubleshooting Procedure StartEND English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System Poland Ukraine Romania Serbia & Montenegro