Gigabyte GA-M52S-S3P user manual Enter= Continue R=Repair F3=Exit

Page 77

When the screen as shown below appears, press <Enter> to continue the driver installation from the floppy disk. The driver installation will be finished in about one minute.

Windows Setup

Setup will load support for the following mass storage device(s):

NVIDIA RAID Driver (required)

NVIDIA nForce Storage Controller (required)

*To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S.

*If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER.

S=Specify Additional Device ENTER=Continue F3=Exit

Figure 5

Step 4:

After the SATA controller driver installation is completed, you can proceed with the Windows XP installation.

WindowsXP Professional Setup

Welcome to Setup.

This port of the Setup program prepares Microsoft(R)

Windows (R) XP to run on your computer.

To set up Windows XP now, press ENTER.

To repair a Windows XP installation using

Recovery Console, press R.

To quit Setup without installing Windows XP, press F3.

Enter= Continue R=Repair	F3=Exit
	Figure 6

English

- 77 -

Appendix

Image 77

Contents GA-M52S-S3P Motherboard Disclaimer CopyrightDocumentation Classifications Identifying Your Motherboard RevisionTable of Contents Drivers Installation Box Contents GA-M52S-S3P Motherboard Layout Block Diagram Installation Precautions Hardware InstallationUSB Product Specifications4 Mbit flash Installing the CPU Installing the CPU and CPU CoolerCPU Socket Locking Lever Installing the CPU Cooler Dual Channel Memory Configuration Installing the MemoryInstalling a Memory Installing an Expansion Card Back Panel Connectors Rear Speaker Out Jack Black Center/Subwoofer Speaker Out Jack OrangeSide Speaker Out Jack Gray Line In Jack BluePwrled Clrcmos Battery Internal ConnectorsGND CPUFAN/SYSFAN Fan Headers FDD Floppy Disk Drive ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors IDE IDE ConnectorBattery Pwrled System Power LED HeaderFpanel Front Panel Header Faudio Front Panel Audio Header Cdin CD In ConnectorSpdifo S/PDIF Out Header Spdifi S/PDIF In HeaderCI Chassis Intrusion Header FUSB1/FUSB2/FUSB3 USB Headers, YellowClrcmos Clearing Cmos Jumper English Chapter Bios Setup Post Screen Logo Screen DefaultStartup Screen Main Menu Sample Bios Version FAcBios Setup Program Function Keys „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationsTime DateIDE Channel 0 Master/Slave IDE Channel 2/3 Master/SlaveDrive a Floppy 3 Mode SupportHalt on MemoryFirst/Second/Third Boot Device Hard Disk Boot PriorityPassword Check HDD S.M.A.R.T. CapabilityInit Display First Away ModeFull Screen Logo Show Integrated Peripherals IDE Prefetch Mode IDE DMA transfer accessOnchip Sata Mode nVIDIA nForce 520 chipset NV Sata Pri-Master RAIDWhen No LAN Cable Is Attached Smart LAN LAN Cable Diagnostic FunctionParallel Port Mode Onboard LAN Boot ROMECP Mode Use DMA Onboard Serial PortModem Ring On PME Event Wake UpHpet Mode Note Power-On by AlarmPower On By Mouse Power On By KeyboardPnP/PCI Configurations Current System/CPU Temperature Reset Case Open StatusSystem/CPU Warning Temperature Case OpenedSystem Smart FAN Control CPU Smart FAN ModePcie Clock CPU FrequencyCPU Clock Ratio Robust Graphics BoosterNormal CPU Vcore DDR2 Voltage ControlCPU Voltage Control Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstalling Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish System Requirements Xpress Recovery2Before You Begin Installing Windows XP and Partitioning the Hard Drive Installation and ConfigurationEnglish Using the Backup Function in Xpress Recovery2 Accessing Xpress Recovery2Exiting Xpress Recovery2 Using the Restore Function in Xpress Recovery2Removing the Backup Updating the Bios with the Q-Flash Utility Bios Update UtilitiesUpdating the Bios English Options and Instructions Updating the Bios with the @BIOS UtilityInstalling and Using @BIOS Update the Bios without Using the Internet Update Function EasyTune 5 Interface Button Information Table EasyTuneWindows Vista ReadyBoost Configuring the Onboard Sata Controller Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below Installing Sata hard drives in your computerConfiguring Sata controller mode in Bios Setup Configuring RAID set in RAID Bios YES BBS Making a Sata RAID/AHCI Driver Diskette Required for Ahci and RAID ModeInstalling Windows XP Installing the Sata RAID/AHCI Driver and Operating SystemSelect Nvidia nForce Storage Controller and press Enter Enter= Continue R=Repair F3=Exit Installing Windows Vista English Configuring Speakers Configuring Audio Input and OutputConfiguring 2/4/5.1/7.1-Channel Audio Configuring AC97 Audio Configuring Sound EffectPdif Installing the S/PDIF In Cable OptionalInstalling the S/PDIF In Cable Conneting a S/PDIF out Cable Configuring S/PDIF outPdif Out Configuring Microphone Recording English Playing the Sound Using the Sound RecorderRecording the Sound Frequently Asked Questions TroubleshootingStart Troubleshooting ProcedureEND English English English English Taiwan Headquarters Contact UsPoland Ukraine Romania Serbia & Montenegro Gigabyte Global Service System