Gigabyte GA-M52S-S3P user manual USB Resume from Suspend, Power-On by Alarm, Hpet Support Note

Page 44

English

USB Resume from Suspend

Allows the system to be awakened from ACPI S3 sleep state by a wake-up signal from the installed USB device. (Default: Enabled)

Power-On by Alarm

Determines whether to power on the system at a desired time. (Default: Disabled) If enabled, set the date and time as following:

Day of Month Alarm: Turn on the system at a specific time on each day or on a specific day in a month.

Time (hh: mm: ss) Alarm: Set the time at which the system will be powered on automatically. Note: When using this function, avoid inadequate shutdown from the operating system or removal of the AC power, or the settings may not be effective.

HPET Support (Note)

Enables or disables High Precision Event Timer (HPET) for Windows® Vista® operating system. (Default: Enabled)

HPET Mode (Note)

Allows you to select the HPET mode for your Windows® Vista® operating system. Select 32-bitmode when you install 32-bit Windows® Vista® ; select 64-bitmode when you install 64-bit Windows® Vista®. (Default: 32-bit mode)

Power On By Mouse

Allows the system to be turned on by a PS/2 mouse wake-up event.

Note: To use this function, you need an ATX power supply providing at least 1A on the 5VSB lead.

Disabled

Disables this function. (Default)

Double Click

Double click on left button on the PS/2 mouse to turn on the system.

Power On By Keyboard

Allows the system to be turned on by a PS/2 keyboard wake-up event. Note: you need an ATX power supply providing at least 1A on the 5VSB lead.

Disabled

Disables this function. (Default)

Password

Set a password with 1~5 characters to turn on the system.

Any KEY

Press any key on the keyboard to turn on the system.

Keyboard 98

Press POWER button on the Windows 98 keyboard to turn on the system.

KB Power ON Password

Set the password when Power On by Keyboard is set to Password. Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept. To turn on the system, enter the password and press <Enter>.

Note: To cancel the password, press <Enter> on this item. When prompted for the password, press <Enter> again without entering the password to clear the password settings.

AC Back Function

Determines the state of the system after the return of power from an AC power loss.

Soft-Off

The system stays off upon the return of the AC power. (Default)

Full-On

The system is turned on upon the return of the AC power.

(Note) Supported on Windows® Vista® operating system only.

 

 

GA-M52S-S3P Motherboard

- 44 -

Page 43 Page 45
Image 44
Page 43 Page 45
Contents GA-M52S-S3P Motherboard Copyright DisclaimerDocumentation Classifications Identifying Your Motherboard RevisionTable of Contents Drivers Installation Box Contents GA-M52S-S3P Motherboard Layout Block Diagram Hardware Installation Installation PrecautionsProduct Specifications USB4 Mbit flash Installing the CPU and CPU Cooler Installing the CPUCPU Socket Locking Lever Installing the CPU Cooler Installing the Memory Dual Channel Memory ConfigurationInstalling a Memory Installing an Expansion Card Back Panel Connectors Center/Subwoofer Speaker Out Jack Orange Rear Speaker Out Jack BlackSide Speaker Out Jack Gray Line In Jack BlueInternal Connectors Pwrled Clrcmos BatteryGND FDD Floppy Disk Drive Connector CPUFAN/SYSFAN Fan HeadersIDE IDE Connector SATAII0/1/2/3 Sata 3Gb/s ConnectorsPwrled System Power LED Header BatteryFpanel Front Panel Header Cdin CD In Connector Faudio Front Panel Audio HeaderSpdifi S/PDIF In Header Spdifo S/PDIF Out HeaderFUSB1/FUSB2/FUSB3 USB Headers, Yellow CI Chassis Intrusion HeaderClrcmos Clearing Cmos Jumper English Chapter Bios Setup Post Screen Logo Screen DefaultStartup Screen Main Menu Sample Bios Version FAcBios Setup Program Function Keys „ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationsDate TimeIDE Channel 0 Master/Slave IDE Channel 2/3 Master/SlaveFloppy 3 Mode Support Drive aHalt on MemoryHard Disk Boot Priority First/Second/Third Boot DevicePassword Check HDD S.M.A.R.T. CapabilityInit Display First Away ModeFull Screen Logo Show Integrated Peripherals IDE DMA transfer access IDE Prefetch ModeOnchip Sata Mode nVIDIA nForce 520 chipset NV Sata Pri-Master RAIDSmart LAN LAN Cable Diagnostic Function When No LAN Cable Is AttachedOnboard LAN Boot ROM Parallel Port ModeECP Mode Use DMA Onboard Serial PortPME Event Wake Up Modem Ring OnPower-On by Alarm Hpet Mode NotePower On By Mouse Power On By KeyboardPnP/PCI Configurations Reset Case Open Status Current System/CPU TemperatureSystem/CPU Warning Temperature Case OpenedCPU Smart FAN Mode System Smart FAN ControlCPU Frequency Pcie ClockCPU Clock Ratio Robust Graphics BoosterNormal CPU Vcore DDR2 Voltage ControlCPU Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Installing Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish System Requirements Xpress Recovery2Before You Begin Installation and Configuration Installing Windows XP and Partitioning the Hard DriveEnglish Accessing Xpress Recovery2 Using the Backup Function in Xpress Recovery2Exiting Xpress Recovery2 Using the Restore Function in Xpress Recovery2Removing the Backup Bios Update Utilities Updating the Bios with the Q-Flash UtilityUpdating the Bios English Options and Instructions Updating the Bios with the @BIOS UtilityInstalling and Using @BIOS Update the Bios without Using the Internet Update Function EasyTune EasyTune 5 Interface Button Information TableWindows Vista ReadyBoost Configuring Sata Hard Drives Configuring the Onboard Sata ControllerTo configure Sata hard drives, follow the steps below Installing Sata hard drives in your computerConfiguring Sata controller mode in Bios Setup Configuring RAID set in RAID Bios YES BBS Required for Ahci and RAID Mode Making a Sata RAID/AHCI Driver DisketteInstalling the Sata RAID/AHCI Driver and Operating System Installing Windows XPSelect Nvidia nForce Storage Controller and press Enter Enter= Continue R=Repair F3=Exit Installing Windows Vista English Configuring Speakers Configuring Audio Input and OutputConfiguring 2/4/5.1/7.1-Channel Audio Configuring Sound Effect Configuring AC97 AudioPdif Installing the S/PDIF In Cable OptionalInstalling the S/PDIF In Cable Conneting a S/PDIF out Cable Configuring S/PDIF outPdif Out Configuring Microphone Recording English Playing the Sound Using the Sound RecorderRecording the Sound Troubleshooting Frequently Asked QuestionsTroubleshooting Procedure StartEND English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System Poland Ukraine Romania Serbia & Montenegro
Top Page Image Contents