Gigabyte GA-K8NS user manual Cpufan / Sysfan Cooler Fan Power Connector, FDD Floppy Connector

Page 19

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and failure. Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

		Pin No.	Definition
		1	GND
		1	GND
		2	+12V

		3	Sense
1		3	Sense

CPU_FAN 1

SYS_FAN

English

5)FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

3433

21

- 19 -

Hardware Installation

Image 19

Contents GA-K8NSrev Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8NSrev .0 Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0SB / SATA1SB Serial ATA Connector IDE1 / IDE2 IDE ConnectorBattery Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center ConnectorClrcmos Clear Cmos USB1 / FUSB2 Front USB ConnectorEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F13 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 2/3 Master Standard Cmos FeaturesTime IDE Channel 0 Master/Slave IDE Channel 1 Master/SlaveDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on Boot Up Floppy Seek Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceInit Display First Password CheckSPP Integrated PeripheralsSata Secndry Master RAID On-Chip LAN Boot ROMIDE Channel 1 Slave RAID Sata Primary Master RAIDOnboard Parallel Port Parallel Port ModeECP Mode Use DMA Onboard Serial PortModem Ring On Power Management SetupResume by Alarm PME Event Wake UpAC Back Function Power On by MousePower On by Keyboard KB Power on PasswordPCI 3 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency/Voltage Control Top Performance Load Optimized DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English English Taiwan Headquarters Contact UsChina Shanghai