Gigabyte GA-K8NS user manual Save & Exit Setup, Exit Without Saving

Page 44

English

2-11 Save & Exit Setup

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

`

Standard CMOS Features

Top Performance

`

Advanced BIOS Features

Load Optimized Defaults

`

Integrated Peripherals

Set Supervisor Password

`

Power Management Setup

Set User Password

`

PnP/PCI Configurations

Save to CMOS and EXITSave(Y/N)?& ExitY Setup

`

PC Health Status

Exit Without Saving

`

Frequency/Voltage Control

 

ESC: Quit

KLJI: Select Item

F8: Q-Flash

F10: Save & Exit Setup

 

Save Data to CMOS

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS. Type "N" will return to Setup Utility.

2-12 Exit Without Saving

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

`

Standard CMOS Features

Top Performance

`

Advanced BIOS Features

Load Optimized Defaults

`

Integrated Peripherals

Set Supervisor Password

`

Power Management Setup

Set User Password

`

PnP/PCI Configurations

Quit Without Saving (Y/N)?Save &NExit Setup

`

PC Health Status

Exit Without Saving

`

Frequency/Voltage Control

 

ESC: Quit

KLJI: Select Item

F8: Q-Flash

F10: Save & Exit Setup

 

Abandon all Data

Type "Y" will quit the Setup Utility without saving to RTC CMOS.

Type "N" will return to Setup Utility.

GA-K8NS(rev. 2.0) Motherboard

- 44 -

Image 44
Contents GA-K8NSrev Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NSrev .0 Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1 / IDE2 IDE Connector SATA0SB / SATA1SB Serial ATA ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F13 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3 MasterHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B Advanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstIntegrated Peripherals SPPOn-Chip LAN Boot ROM IDE Channel 1 Slave RAIDSata Primary Master RAID Sata Secndry Master RAIDParallel Port Mode ECP Mode Use DMAOnboard Serial Port Onboard Parallel PortPower Management Setup Resume by AlarmPME Event Wake Up Modem Ring OnPower On by Mouse Power On by KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 3 IRQ AssignmentPC Health Status Frequency/Voltage Control Load Optimized Defaults Top PerformanceSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai