Gigabyte user manual GA-K8NSrev .0 Motherboard Layout

Page 6

GA-K8NS(rev. 2.0) Motherboard Layout

KB_MS

R_USB

ATX_12V

COMA
	LPT
COMB
USB	LAN

AUDIO1

F_AUDIO CPU_FAN

	IT8712
ICS 1883	AGP

Socket 754

SATA0_SB SATA1_SB

GA-K8NS














	DDR1 DDR2 DDR3

	ATX	FAN
	ATX	SYS
		SYS

FDD

IDE1

IDE2

CLR_CMOS

BATTERY

	CEN	CD_IN
	SUR	CD_IN
	SUR

SPDIF_IO CODEC

	PCI1	nVIDIA®
		nVIDIA®
		nForceTM 3 250
	PCI2
	PCI3	F_USB2
	PCI3
		F_USB1
	PCI4	BIOS
	PCI5	F_PANEL
	PCI5	PWR_LED
		PWR_LED

- 6 -

Image 6

Contents GA-K8NSrev Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NSrev .0 Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1 / IDE2 IDE Connector SATA0SB / SATA1SB Serial ATA ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F13 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on First / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekPassword Check Init Display FirstIntegrated Peripherals SPPSata Primary Master RAID On-Chip LAN Boot ROMIDE Channel 1 Slave RAID Sata Secndry Master RAIDOnboard Serial Port Parallel Port ModeECP Mode Use DMA Onboard Parallel PortPME Event Wake Up Power Management SetupResume by Alarm Modem Ring OnKB Power on Password Power On by MousePower On by Keyboard AC Back FunctionPnP/PCI Configurations PCI 3 IRQ AssignmentPC Health Status Frequency/Voltage Control Load Optimized Defaults Top PerformanceSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing and UAJ IntroductionAuto-detecting Manual setting Enable UAJ functionUAJ Introduction Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai