Gigabyte GA-K8NS Power On by Mouse, Power On by Keyboard, KB Power on Password, AC Back Function

Page 38

English

Power On by Mouse

Disabled

Disable this function. (Default value)

Double Click

Double click on PS/2 mouse left button to power on the system.

Power On by Keyboard

Password

Enter from 1 to 5 characters to set the Keyboard Power On Password.

Disabled

Disable this function. (Default value)

Any KEY

Press any key to power on the system.

Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to power on the system.

KB Power ON Password

When "Power On by Keyboard" set at Password, you can set the password here.

Enter Input password (from 1 to 5 characters) and press Enter to set the Keyboard Power On password.

AC BACK Function

Soft-Off

When AC-power back to the system, the system will be in "Off" state.

 

(Default value)

Full-On

When AC-power back to the system, the system always in "On" state.

GA-K8NS(rev. 2.0) Motherboard

- 38 -

Image 38
Contents GA-K8NSrev Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NSrev .0 Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1 / IDE2 IDE Connector SATA0SB / SATA1SB Serial ATA ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F13 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B First / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekPassword Check Init Display FirstIntegrated Peripherals SPPSata Primary Master RAID On-Chip LAN Boot ROMIDE Channel 1 Slave RAID Sata Secndry Master RAIDOnboard Serial Port Parallel Port ModeECP Mode Use DMA Onboard Parallel PortPME Event Wake Up Power Management SetupResume by Alarm Modem Ring OnKB Power on Password Power On by MousePower On by Keyboard AC Back FunctionPnP/PCI Configurations PCI 3 IRQ AssignmentPC Health Status Frequency/Voltage Control Load Optimized Defaults Top PerformanceSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai