Gigabyte GA-K8NS user manual PC Health Status

Page 40

English

2-6	PC Health Status

		CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
			PC Health Status
	Vcore		OK			Item Help
	DDR25V		OK		Menu Level`
	+3.3V		OK
	+12V		OK
	Current CPU Temperature		36oC
	Current CPU FAN Speed		3245 RPM
	Current SYSTEM FAN Speed		0	RPM
	CPU Warning Temperature		[Disabled]
	CPU FAN Fail Warning		[Disabled]
	SYSTEM FAN Fail Warning		[Disabled]
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
		F5: Previous Values		F7: Optimized Defaults

Current Voltage(V) Vcore / DDR25V / +3.3V / +12V

Detect system's voltage status automatically.

Current CPU Temperature

Detect CPU temperature automatically.

Current CPU/SYSTEM FAN Speed (RPM)

Detect CPU//SYSTEM Fan speed status automatically.

CPU Warning Temperature

60oC / 140oF	Monitor CPU temperature at 60oC / 140oF.
70oC / 158oF	Monitor CPU temperature at 70oC / 158oF.
80oC / 176oF	Monitor CPU temperature at 80oC / 176oF.
90oC / 194oF	Monitor CPU temperature at 90oC / 194oF.
Disabled	Disable this function. (Default value)

CPU/SYSTEM FAN Fail Warning

Disabled	Disable CPU/SYSTEM fan fail warning function. (Default value)
Enabled	Enable CPU/SYSTEM fan fail warning function.

GA-K8NS(rev. 2.0) Motherboard

- 40 -

Image 40

Contents GA-K8NSrev Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NSrev .0 Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1 / IDE2 IDE Connector SATA0SB / SATA1SB Serial ATA ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F13 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3 MasterDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on Advanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstIntegrated Peripherals SPPOn-Chip LAN Boot ROM IDE Channel 1 Slave RAIDSata Primary Master RAID Sata Secndry Master RAIDParallel Port Mode ECP Mode Use DMAOnboard Serial Port Onboard Parallel PortPower Management Setup Resume by AlarmPME Event Wake Up Modem Ring OnPower On by Mouse Power On by KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 3 IRQ AssignmentPC Health Status Frequency/Voltage Control Load Optimized Defaults Top PerformanceSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English English Contact Us Taiwan HeadquartersChina Shanghai