Gigabyte GA-K8NULTRA-SLI, GA-K8N-SLI 17 F11394/F21394 Ieee 1394 Connectors, Clrcmos Clear Cmos

Page 31

17)F1_1394/F2_1394 (IEEE 1394 Connectors)

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, high bandwidth and hot plug. Be careful with the polarity of the IEEE1394 connector. Check the pin assignment carefully while you connect the IEEE1394 cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional IEEE1394 cable, please contact your local dealer. IEEE1394b can approach the

maximum speed to 800Mb/S, but the speed can be achieved only when you use particular

IEEE1394b cable.

 

 

2

16

 

 

 

 

 

 

F2_1394

 

F1_1394

2

10

1

15

Pin No.

Definition

1

9

 

1

Power

 

 

 

Pin No.

Definition

2

Power

3

TPA1+

1

 

TPA0+

 

4

TPA1-

2

 

TPA0-

 

5

GND

3

 

GND

 

6

GND

4

 

GND

 

7

TPB1+

5

 

TPB0+

 

8

TPB1-

6

 

TPB0-

 

9

Power

7

 

No Pin

 

10

Power

8

 

Power

 

11

TPA2+

9

 

Power

 

12

TPA2-

10

 

GND

 

13

GND

 

 

 

 

 

 

14

No Pin

 

 

 

15

TPB2+

 

 

 

16

TPB2-

18)CLR_CMOS (Clear CMOS)

You may clear the CMOS data to its default values by this header. To clear CMOS, temporarily short 1-2 pin. Default doesn't include the jumper to prevent from improper use of this header.

Open: Normal

1

Short: Clear CMOS

1

English

Only for GA-K8N Ultra-SLI.

Only for GA-K8N Pro-SLI.

 

 

 

- 31 -

Hardware Installation

 

Image 31
Contents GA-K8N-SLI Motherboard GA-K8N Pro-SLI Feb GA-K8N-SLI Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8N Ultra-SLI or GA-K8N Pro-SLI/GA-K8N-SLI GA-K8NUltra-SLI/GA-K8NPro-SLI/GA-K8N-SLIMotherboardLayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantySATA3SII Feature SummaryBios Installation of the CPU Installation of the CPU and Fan Heat SinkInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Before You Begin Setup of SLI Scalable Link Interface ConfigurationEnabling SLI Mode Graphics card I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out Rear Speaker OutATX12V/ATX Power Connector Nbfan Chip Fan Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector FDD FDD ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Pwrled Cdin CD In ConnectorIrcir USB1 / FUSB2/FUSB3 Front USB ConnectorClrcmos Clear Cmos 17 F11394/F21394 Ieee 1394 ConnectorsBattery Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F6a „ Exit Without Saving „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave TimeIDE Channel 2/3/4/5 Master Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on First / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Init Display First Password CheckIntegrated Peripherals IDE Primary Master RAID On-Chip LAN Boot ROMOn-Chip MAC Lan NV IDE/SATA RAID function NoteNV Sata 2 Primary RAID IDE Prefetch ModeOnBoard LAN Boot ROM NV Sata 2 class codeNoteOnboard IrDA Port Parallel Port ModeECP Mode Use DMA Onboard Serial PortLegacy USB Storage detect Power Management SetupPnP/PCI Configurations DDR25V PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureTemp Limit of High Speed Default temperature 60oC Temp of FAN turn off Default temperature 0oCTemp Limit of Low Speed Default temperature 20oC Temp Limit of Mid Speed Default temperature 50oCK8 CPU Clock Ratio MB Intelligent TweakerM.I.THT Frequency ratio CPU FrequencyWrite Recovery Time Twr DDR clock/Timing ModeRAS# to CAS# delay Trcd Row to Row delay TrrdCPU Spread Spectrum Refresh Rate TrefRead Preamble value Async Latency valueTop Performance Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations What is Dual Bios Technology? Flash Bios Method IntroductionHow to use Dual Bios and Q-Flash Utility? Halt On Error DisableDefault, Enable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Auto Recovery EnableDefault, DisableBefore You Begin Method 1 Q-FlashTMUtilityTask menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID driversStereo Speakers Connection and Settings Introduction of audio connectors5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English Auto-detecting Jack-Sensing IntroductionManual setting AMI Bios Beep Codes TroubleshootingEnglish Taiwan Headquarters Contact UsChina Shanghai