Gigabyte GA-K8N-SLI, GA-K8NULTRA-SLI user manual Battery

Page 32

English

19) BATTERY

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

If you want to erase CMOS...

1.Turn OFF the computer and unplug the power cord.

2.Take out the battery gently and put it aside for about 10 minutes. (Or you can use a metal object to connect the positive and nega- tive pins in the battery holder to makethem short for one minute.)

3.Re-install the battery.

4.Plug the power cord and turn ON the computer.

K8 nForce4 SLI Series Motherboard

- 32 -

Image 32
Contents GA-K8N-SLI Motherboard GA-K8N Pro-SLI Feb GA-K8N-SLI Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NUltra-SLI/GA-K8NPro-SLI/GA-K8N-SLIMotherboardLayout GA-K8N Ultra-SLI or GA-K8N Pro-SLI/GA-K8N-SLIBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary SATA3SIIBios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Setup of SLI Scalable Link Interface Configuration Before You BeginEnabling SLI Mode Graphics card I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutRear Speaker Out Side Speaker OutATX12V/ATX Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power Connector Nbfan Chip Fan Power ConnectorFDD FDD Connector IDE1 / IDE2 IDE ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2/FUSB3 Front USB Connector Ircir17 F11394/F21394 Ieee 1394 Connectors Clrcmos Clear CmosBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F6a „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without SavingIDE Channel 2/3/4/5 Master TimeIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B Boot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Password Check Init Display FirstIntegrated Peripherals On-Chip LAN Boot ROM On-Chip MAC LanNV IDE/SATA RAID function Note IDE Primary Master RAIDIDE Prefetch Mode OnBoard LAN Boot ROMNV Sata 2 class codeNote NV Sata 2 Primary RAIDParallel Port Mode ECP Mode Use DMAOnboard Serial Port Onboard IrDA PortPower Management Setup Legacy USB Storage detectPnP/PCI Configurations PC Health Status DDR25VCurrent CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature Current VoltageV Vcore / DDR25V / +3.3V / +12VTemp of FAN turn off Default temperature 0oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp Limit of High Speed Default temperature 60oCMB Intelligent TweakerM.I.T HT Frequency ratioCPU Frequency K8 CPU Clock RatioDDR clock/Timing Mode RAS# to CAS# delay TrcdRow to Row delay Trrd Write Recovery Time TwrRefresh Rate Tref Read Preamble valueAsync Latency value CPU Spread SpectrumTop Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions How to use Dual Bios and Q-Flash Utility? Flash Bios Method IntroductionWhat is Dual Bios Technology? Wide Range Protection DisableDefault, Enable Boot From Main BIOSDefault, Backup BiosAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginExploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv Menu5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English English Jack-Sensing Introduction Auto-detectingManual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai