Gigabyte GA-K8N-SLI NV Sata 2 class codeNote, NV Sata 2 Primary RAID, NV Sata 2 Secondary RAID

Page 42

English

NV SATA 2 class code(Note)

0101	Set NV SATA 2 class code to 0101. (Default value)
0104	Set NV SATA 2 class code to 0104.

NV SATA 2 Primary RAID

Enabled	Enable 2nd SATA primary RAID function. (Default value)
Disabled	Disable this function.

NV SATA 2 Secondary RAID

Enabled	Enable 2nd SATA secondary RAID function. (Default value)
Disabled	Disable this function.

IDE Prefetch Mode

Enabled	Enable IDE Prefetch mode. (Default value)
Disabled	Disable IDE Prefetch mode.

USB Memory Type

SHADOW	Set USB memory type to SHADOW. (Default value)
Base Memory(640K)	Set USB memory type to base memory(640K).

AC97 Audio

Auto	Enable onboard AC'97 audio function. (Default value)
Disabled	Disable this function.

Onboard 1394

Enabled	Enable onboard IEEE1394 function.(Default value)
Disabled	Disable onboard IEEE1394 function.

Onboard LAN control (LAN1)

Enabled	Enable onboard LAN chip function.(Default value)
Disabled	Disable onboard LAN chip function.

OnBoard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled	Enable this function.
Disabled	Disable this function. (Default value)

SATA RAID-5/ATA controller (Controlled by Sil3114 chip)

This option is to enable or disable the Sil3114 controller.

Enabled	Enable onboard Serial ATA Chip.(Default value)
Disabled	Disable onboard Serial ATA Chip.

SATA controller Function (Controlled by Sil3114 chip)

RAID-5	Set Sil3114 Serial ATA Chip to RAID mode.(Default value)
ATA	Set Sil3114 Serial ATA Chip to ATA mode.

(Note) When using driver version 1.2, please enable "NV IDE/SATA RAID function" if you wish to create RAID data drive or install O.S. on the RAID drive.

And manually set "NV SATA1/NV SATA 2 class code" from 0101 to 0104.

If your SATA hard drive is connected to the SATA0 or SATA1 connector , please set "NV SATA1 class code" to 0104. If your SATA hard drive is connected to the SATA2 or SATA3 connector , please set "NV SATA2 class code" to 0104.

Only for GA-K8N Ultra-SLI.	Only for GA-K8N Pro-SLI.
K8 nForce4 SLI Series Motherboard	- 42 -

Image 42

Contents GA-K8N-SLI Motherboard GA-K8N Pro-SLI Feb GA-K8N-SLI Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NUltra-SLI/GA-K8NPro-SLI/GA-K8N-SLIMotherboardLayout GA-K8N Ultra-SLI or GA-K8N Pro-SLI/GA-K8N-SLIBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary SATA3SIIBios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Setup of SLI Scalable Link Interface Configuration Before You BeginEnabling SLI Mode Graphics card I/O Back Panel Introduction Rear Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out Side Speaker OutATX12V/ATX Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power Connector Nbfan Chip Fan Power ConnectorFDD FDD Connector IDE1 / IDE2 IDE ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2/FUSB3 Front USB Connector Ircir17 F11394/F21394 Ieee 1394 Connectors Clrcmos Clear CmosBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F6a „ Save & Exit Setup „ Set Supervisor Password„ Set User Password „ Exit Without SavingTime IDE Channel 0 Master, Slave, IDE Channel 1 Master, SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on Hard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Init Display FirstIntegrated Peripherals NV IDE/SATA RAID function Note On-Chip LAN Boot ROMOn-Chip MAC Lan IDE Primary Master RAIDNV Sata 2 class codeNote IDE Prefetch ModeOnBoard LAN Boot ROM NV Sata 2 Primary RAIDOnboard Serial Port Parallel Port ModeECP Mode Use DMA Onboard IrDA PortPower Management Setup Legacy USB Storage detectPnP/PCI Configurations PC Health Status DDR25VCPU Warning Temperature Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM Current VoltageV Vcore / DDR25V / +3.3V / +12VTemp Limit of Mid Speed Default temperature 50oC Temp of FAN turn off Default temperature 0oCTemp Limit of Low Speed Default temperature 20oC Temp Limit of High Speed Default temperature 60oCCPU Frequency MB Intelligent TweakerM.I.THT Frequency ratio K8 CPU Clock RatioRow to Row delay Trrd DDR clock/Timing ModeRAS# to CAS# delay Trcd Write Recovery Time TwrAsync Latency value Refresh Rate TrefRead Preamble value CPU Spread SpectrumTop Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction What is Dual Bios Technology?How to use Dual Bios and Q-Flash Utility? Auto Recovery EnableDefault, Disable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginEntering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuIntroduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English Jack-Sensing Introduction Auto-detectingManual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai