Gigabyte GA-K8N-SLI, GA-K8NULTRA-SLI user manual PC Health Status, DDR25V

Page 46

English

2-6 PC Health Status

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

PC Health Status

Vcore	OK
DDR25V	OK
+3.3V	OK
+12V	OK
Current CPU Temperature	34oC
Current CPU FAN Speed	3183 RPM
Current POWER FAN Speed	0	RPM
Current SYSTEM FAN Speed	0	RPM
CPU Warning Temperature	[Disabled]
CPU FAN Fail Warning	[Disabled]
CPU Smart FAN Control	[Disabled]
CPU FAN Manual Control	[Disabled]
x CPU FAN: Low speed	8
x CPU FAN: Mid speed	12
x CPU FAN: High speed	80
x Temp of FAN turn off	0
x Temp Limit of Low Speed	20
x Temp Limit of Mid Speed	50

Item Help

Menu Level

: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit			F1: General Help
	F5: Previous Values		F7: Optimized Defaults
	CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
		PC Health Status
x Temp Limit of High Speed		60					Item Help
x Temp of full FAN speed		70				Menu Level

: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values		F7: Optimized Defaults

The CPU fan runs at full speed when both CPU Smart FAN Control and CPU FAN Manual Control are disabled.

K8 nForce4 SLI Series Motherboard

- 46 -

Image 46

Contents GA-K8N-SLI Motherboard GA-K8N Pro-SLI Feb GA-K8N-SLI Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NUltra-SLI/GA-K8NPro-SLI/GA-K8N-SLIMotherboardLayout GA-K8N Ultra-SLI or GA-K8N Pro-SLI/GA-K8N-SLIBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary SATA3SIIBios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Setup of SLI Scalable Link Interface Configuration Before You BeginEnabling SLI Mode Graphics card I/O Back Panel Introduction Rear Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out Side Speaker OutATX12V/ATX Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power Connector Nbfan Chip Fan Power ConnectorFDD FDD Connector IDE1 / IDE2 IDE ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2/FUSB3 Front USB Connector Ircir17 F11394/F21394 Ieee 1394 Connectors Clrcmos Clear CmosBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F6a „ Save & Exit Setup „ Set Supervisor Password„ Set User Password „ Exit Without SavingIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave TimeIDE Channel 2/3/4/5 Master Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on First / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Password Check Init Display FirstIntegrated Peripherals NV IDE/SATA RAID function Note On-Chip LAN Boot ROMOn-Chip MAC Lan IDE Primary Master RAIDNV Sata 2 class codeNote IDE Prefetch ModeOnBoard LAN Boot ROM NV Sata 2 Primary RAIDOnboard Serial Port Parallel Port ModeECP Mode Use DMA Onboard IrDA PortPower Management Setup Legacy USB Storage detectPnP/PCI Configurations PC Health Status DDR25VCPU Warning Temperature Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM Current VoltageV Vcore / DDR25V / +3.3V / +12VTemp Limit of Mid Speed Default temperature 50oC Temp of FAN turn off Default temperature 0oCTemp Limit of Low Speed Default temperature 20oC Temp Limit of High Speed Default temperature 60oCCPU Frequency MB Intelligent TweakerM.I.THT Frequency ratio K8 CPU Clock RatioRow to Row delay Trrd DDR clock/Timing ModeRAS# to CAS# delay Trcd Write Recovery Time TwrAsync Latency value Refresh Rate TrefRead Preamble value CPU Spread SpectrumTop Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations What is Dual Bios Technology? Flash Bios Method IntroductionHow to use Dual Bios and Q-Flash Utility? Auto Recovery EnableDefault, Disable Wide Range Protection DisableDefault, EnableBoot From Main BIOSDefault, Backup Bios Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginEntering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv MenuStereo Speakers Connection and Settings Introduction of audio connectors5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English Jack-Sensing Introduction Auto-detectingManual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai