Gigabyte GA-K8NULTRA-SLI user manual GA-K8NUltra-SLI/GA-K8NPro-SLI/GA-K8N-SLIMotherboardLayout

Page 8

GA-K8NUltra-SLI/GA-K8NPro-SLI/GA-K8N-SLIMotherboardLayout

SPDIF_I

SPDIF_O

KB_MS

ATX_12V

	LPT
COMA
USB	LAN2
USB	LAN1

AUDIO1CPU_FAN

	AUDIO2	VITESSE
	AUDIO2	8201 phy
		8201 phy

F_AUDIO PCIE_1

Marvell 8053

PCIE_2

CODEC	IN
	CD_

Socket 939

Backup Main

BIOS BIOS

PCIE_16_1

SLI Switch Module Socket

PCIE_16_2

PCI1

GA-K8N Ultra-SLI or GA-K8N Pro-SLI/GA-K8N-SLI

TSB82AA2

DDR1

DDR2

DDR3

DDR4

nVIDIA® nForce4 SLI

ATX

PWR_FAN

IDE2

IDE1 FDD

BATTERY FAN_ NB CLR_CMOS S_ATA1_SB

S_ATA0_SB

S_ATA3_SB S_ATA2_SB

F_PANEL

IT8712	PCI2	TSB81BA3

		F1_1394 F2_1394
	IR_CIR

Sil3114

PWR_LED

						F_USB3



				FAN		F_USB2
				FAN
				SYS
						F_USB1

SATA0 SII

SATA1 SII

SATA2 SII

SATA3 SII

Only for GA-K8N Ultra-SLI.

Only for GA-K8N Pro-SLI.

- 8 -

Image 8

Contents GA-K8N-SLI Motherboard GA-K8N Pro-SLI Feb GA-K8N-SLI Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NUltra-SLI/GA-K8NPro-SLI/GA-K8N-SLIMotherboardLayout GA-K8N Ultra-SLI or GA-K8N Pro-SLI/GA-K8N-SLIBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary SATA3SIIBios Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Setup of SLI Scalable Link Interface Configuration Before You BeginEnabling SLI Mode Graphics card I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutRear Speaker Out Side Speaker OutATX12V/ATX Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power Connector Nbfan Chip Fan Power ConnectorFDD FDD Connector IDE1 / IDE2 IDE ConnectorFaudio Front Audio Panel Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2/FUSB3 Front USB Connector Ircir17 F11394/F21394 Ieee 1394 Connectors Clrcmos Clear CmosBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F6a „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without SavingIDE Channel 2/3/4/5 Master TimeIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B Boot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Password Check Init Display FirstIntegrated Peripherals On-Chip LAN Boot ROM On-Chip MAC LanNV IDE/SATA RAID function Note IDE Primary Master RAIDIDE Prefetch Mode OnBoard LAN Boot ROMNV Sata 2 class codeNote NV Sata 2 Primary RAIDParallel Port Mode ECP Mode Use DMAOnboard Serial Port Onboard IrDA PortPower Management Setup Legacy USB Storage detectPnP/PCI Configurations PC Health Status DDR25VCurrent CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature Current VoltageV Vcore / DDR25V / +3.3V / +12VTemp of FAN turn off Default temperature 0oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp Limit of High Speed Default temperature 60oCMB Intelligent TweakerM.I.T HT Frequency ratioCPU Frequency K8 CPU Clock RatioDDR clock/Timing Mode RAS# to CAS# delay TrcdRow to Row delay Trrd Write Recovery Time TwrRefresh Rate Tref Read Preamble valueAsync Latency value CPU Spread SpectrumTop Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions How to use Dual Bios and Q-Flash Utility? Flash Bios Method IntroductionWhat is Dual Bios Technology? Wide Range Protection DisableDefault, Enable Boot From Main BIOSDefault, Backup BiosAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginExploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Cd bootdrv Menu5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English English Jack-Sensing Introduction Auto-detectingManual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai